Canon Colorado M Series Скачать руководство пользователя страница 143 | Manualshive

Страница: 143 / 378

background image

Transport media by manual control

Introduction

You can move the media before and between jobs.

Procedure

1.

On the operator panel tap on the [Output] icon.

2.

Select [Manual control] as [Transport mode].

3.

Select the transport direction.
• [Forward ] will transport the media towards the winder.
• [Backward ] will transport the media back in the direction of the drawer.

4.

Tap on [Start].
The media will move in the direction you selected. A stop option becomes available.

IMPORTANT

When media transport is started in the forward direction, the system will keep spooling
media until the roll is empty.

NOTE

Backward transport is limited by the available media on the platen and the winder. No
media will be removed from the winder.
It is not possible to move printed media back into the drawer.

5.

Tap on [Stop] to stop the transport.

NOTE

Depending on the settings [Moist sensitivity] and [Auto media advance] the actual print
position can vary. [Moist sensitivity] timers are restarted after the movement has been
stopped.

Transport media by manual control

Chapter 4 - Handle the media

143

«
...
141
142
143
144
145
...
»

Содержание Colorado M Series



























































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Colorado M Series

Бренд: Oce Страницы: 255

Бренд: EasyThreed Страницы: 15

PR-INT-MX-RAVAS-ABLE

Бренд: Ravas Страницы: 26

Бренд: Kyocera Страницы: 13

Бренд: Konica Minolta Страницы: 2

Бренд: TP-Link Страницы: 16

Бренд: Oki Страницы: 204

Бренд: Oki Страницы: 137

Бренд: MIMAKI Страницы: 20

Бренд: Tektronix Страницы: 178

Бренд: Oki Страницы: 110

Бренд: SEWOO Страницы: 8

Бренд: Kimo Страницы: 2

Бренд: EcLine Страницы: 72

Бренд: OKIDATA Страницы: 158

Бренд: Canon Страницы: 327

CraftBot PlusPro

Бренд: CraftUnique Страницы: 2

Бренд: Lexmark Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды