Canon Colorado M Series Скачать руководство пользователя страница 115 | Manualshive

Страница: 115 / 378

background image

Load flexible media for inside printing

Introduction

When you load flexible media in the printer, such as canvas and textiles, manual feeding and the
use of the tension bar are recommended. You can configure the settings for manual feeding and
the tension bar in the RIP. You can also use the help of rigid media to feed the flexible media
more easily in the paper path.

Follow the procedure below to attach a leading strip of rigid media to your flexible media. This
technique will prevent media transportation issues.

In case you cut the media after printing, the media roll is unloaded. To print on the flexible media
again you must redo the procedure to attach a leading strip of rigid media.

This procedure describes the steps for inside printing. For inside printing it is recommended to
load the flexible media in position 1.

Video:

How to print on flexible media

(video shows outside printing).

Before you begin

Before you load a roll on the printer:
• Make sure you have added a media profile with the correct media type via the RIP. For more

information, see

Configure media in the RIP on page 44

• Check the media width of your roll before loading. When your media width is not present in the

list on the operator panel, you can type it in.

• Put on gloves to avoid pollution of the paper by your fingerprints.

CAUTION

• Watch your fingers when you handle the media roll.
• Loading heavy media, 25 kg (55 lb) or more, has to be done by two people or with the help of

external lifting tools.

IMPORTANT

• Do not use dented or damaged media rolls to prevent damage to the printheads.
• Only open the media drawer when the indicator light on the drawer is on. Do not open the

drawer when the light is off, you can damage the machine.

Procedure

1.

Pull firmly to open the media drawer.

2.

Load the media roll of flexible media in position 1, with the media flap on top pointing away from
you.

Load flexible media for inside printing

Chapter 4 - Handle the media

115

«
...
113
114
115
116
117
...
»

Содержание Colorado M Series



























































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Colorado M Series

Бренд: Oki Страницы: 16

Бренд: Xerox Страницы: 23

Бренд: IBM Страницы: 113

Бренд: IBM Страницы: 16

Бренд: IBM Страницы: 214

Бренд: Oce Страницы: 192

Бренд: Oce Страницы: 22

Бренд: Oce Страницы: 41

Бренд: Oce Страницы: 28

Бренд: Oce Страницы: 6

Бренд: QMS Страницы: 104

Бренд: Oce Страницы: 386

Бренд: Oce Страницы: 2

Бренд: Oce Страницы: 27

Бренд: Oce Страницы: 324

da Vinci 2.0 Duo

Бренд: XYZ Printing Страницы: 7

da Vinci Jr.1.0

Бренд: XYZ Printing Страницы: 8

Бренд: Tektron Страницы: 72

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды