Canon Colorado 1630 Скачать руководство пользователя страница 296 | Manualshive

Страница: 296 / 388

Canon Colorado 1630 Скачать руководство пользователя страница 296

Restore a backup

Introduction

When you have made a backup you can restore it.

Before you begin

You need to have a backup created before. It is highly recommended to have exported a backup.
For more information, see

Make a backup on page 295

.

Procedure

1.

Open the settings editor.

2.

Click on [Support]

→

[Backups].

3.

In case of an external backup, exported during a backup operation, click on [Import]. Browse to
the external backup and confirm the import operation.
When imported with a confidential data passphrase and this passphrase does not match the
passphrase of the backup, the screen displays a warning that the confidential data is not available
for restoring.

4.

Check the box in front of the backup file.

5.

Click on [Restore user configuration].

6.

Click on [Ok] to restore the configuration.

Restore a backup

296

Chapter 8 - Configure the network and security settings

«
...
294
295
296
297
298
...
»

Содержание Colorado 1630





































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды