Canon Colorado 1630 Скачать руководство пользователя страница 276 | Manualshive

Страница: 276 / 388

Canon Colorado 1630 Скачать руководство пользователя страница 276

Change the System administrator password

Introduction

For security reasons it is advised to change the System administrator password during
installation or immediately after. Next to that, you should change the password periodically.

Before you begin

Log in as System administrator in the settings editor.

Change the password

1. Open the settings editor.
2. Click on [Configuration]

→

[Users].

3. Check the box in front of [System administrator] and click on the [Edit] icon above.

4. In the window, fill in [Password] and [Confirm password] with your new password.
5. Click [ Ok] to save the password.

Reset the System administrator account

It is also possible to reset the System administrator account and go back to the default values.
Click on [Configuration]

→

[Security]

→

[Restore factory-defined account values] and click on [Ok].

A password prompt will pop up. It is possible to send a recover email. The mail server must be
configured to be able to do this.

Change the System administrator password

276

Chapter 8 - Configure the network and security settings

«
...
274
275
276
277
278
...
»

Содержание Colorado 1630





































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды