Canon Colorado 1630 Скачать руководство пользователя страница 182 | Manualshive

Страница: 182 / 388

Canon Colorado 1630 Скачать руководство пользователя страница 182

Clean the matrix plate area

Introduction

The printheads are located in the matrix plate. The printheads and the matrix plate area need to
be cleaned regularly. As well as the anti-reflective strips and mirror edges.

NOTE

The operator panel gives a warning to perform this procedure at least once a month, and

depending on the ink usage, between 7 and 30 days. To guarantee the print quality it is

recommended to clean the matrix plate once a week. Cleaning the matrix plate is the first part of

this procedure, step 1 to step 10.

During the use of the printer, dust and fibers from the media can accumulate on the edges of the
anti-reflective strips and mirrors of the printhead carriage. If these fibers touch the surface of the
paper during printing, they can wipe through the uncured ink and can cause print quality issues.

These print quality issues can easily be mistaken for printhead issues, as these fibers are stuck to
the carriage. To prevent unnecessary service calls or printhead replacements, the edges of the
anti-reflective strips and mirrors need to be cleaned regularly.

Clean the matrix plate

Before you begin

Use Colorado 1630 prescribed:
• Microflex gloves for handling ink
• Foams and swabs
• Matrix plate cleaning tool
• Cleaning liquid (Cleaner MB - methyl benzoate)
• Cleaner IPA

NOTE

For information on the prescribed maintenance materials, see

List of Colorado 1630

maintenance materials on page 255

IMPORTANT

There are 2 types of swabs. The cleaning procedure depends on the width of the swab.

CAUTION

Wear the prescribed gloves when contact with ink or maintenance materials is possible. Gloves

should always overlap sleeves. Follow the Safety Data Sheets (SDS) guidelines carefully in

order to ensure maximum safety.

IMPORTANT

Use the prescribed cleaning liquid. Do not use any other cleaners.

Clean the matrix plate area

182

Chapter 6 - Maintain the system

«
...
180
181
182
183
184
...
»

Содержание Colorado 1630





































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды