Canon Colorado 1630 Скачать руководство пользователя страница 138 | Manualshive

Страница: 138 / 388

Canon Colorado 1630 Скачать руководство пользователя страница 138

Print double-sided with automatic cut

Introduction

Colorado 1630 offers the possibility to print on the inside as well as on the outside of the media,
which indirectly provides the user a way to print double-sided.

To print double-sided you print on the inside of the media.

How to print double-sided

Before you begin

RIP

• In [Media Characteristics], set automatic advance correction (AAC) to [Enhanced] to achieve an

optimal x-registration.
AAC prints yellow or black markers on the media that the printer uses as guidance to optimize
the media step accuracy. See "Change the media settings" in the operation guide.

• In [Placement strategy]

→

[General], make sure that the left and right are identical.

• In [Placement strategy]

→

[Options], make sure that the space between copies values are 0.

Printer

• Use the tension bar (locked).

In case the media is normally (single-sided) printed without tension bar, switch to the locked
tension bar mode.
You can change this tension bar setting for the media type in the RIP. Change from [No tension
bar] to [Locked tension bar].

• Use a matte print mode, preferably the same mode for both sides.
• Do not enable automatic media advance or moist sensitivity settings.
• If necessary calibrate the media.

Tools

• A media suitable for double sided printing.
• 2 empty cores with the same width as the media you want to use.
• A roll of tape.

Print double-sided with automatic cut

138

Chapter 4 - Handle the media

«
...
136
137
138
139
140
...
»

Содержание Colorado 1630





































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды