Canon Colorado 1630 Скачать руководство пользователя страница 131

Страница: 131 / 388

Print without winding

Introduction

You can also print without winding. Media that is printed without winding can be transported
well and is not too weak.

Before you begin

• Check the media category of your media. Media categories that need a tension bar cannot be

printed without winding.

• Printing without winding is set in the media type configuration in the RIP software. For printing

without winding you must select [no tension bar] under [Winding tension]. For more
information, see

Change the media settings on page 67

• The printer is ready to print.

Procedure

On the operator panel tap on the [Output] icon.

Tap on [Output configuration].

Make sure [Wind the output] is set to [No].

NOTE

Make sure you set the output configuration in time, as you cannot change the
configuration once the media has passed the clamp.

Print without winding

Chapter 4 - Handle the media

131

Содержание Colorado 1630





































































































































































































































































































































































































Результаты поиска

Содержание Colorado 1630

Отзывы:

Бренды по названию

Популярные бренды

Canon Colorado 1630, Руководство по эксплуатации

Результаты поиска

Содержание Colorado 1630

Отзывы:

Бренды по названию

Популярные бренды