
5
5
5-59
5-59
Troubleshooting > Service Mode > Service Mode List > NETWORK GR.
Troubleshooting > Service Mode > Service Mode List > NETWORK GR.
■
PANEL LOCK GR.
Items
Description
Setting Range
PANEL LOCK
To perform access restriction for each key on the Control
Panel.
■
F/W UPDATE GR.
Items
Description
Setting Range
USB
To use USB to update firmware
Yes/No*
NETWORK
To use network to update firmware
Yes/No*
USB STORAGE ALL
To update various firmware required for the
device to those stored in the USB storage.
Update is executed even if any of the firmware
is lacking in the USB storage
Yes/No*
CONT
To update the controller firmware of the device
to the one stored in the USB storage
Yes/No*
BOOT
To update the startup firmware of the device to
the one stored in the USB storage
Yes/No*
DCON
To update the engine firmware of the device to
the one stored in the USB storage.
Yes/No*
CDS
Firmware auto/manual update function by MEAP
application (updater)
Yes/No*
■
NETWORK GR.
Items
Description
Setting Range
DNSTRANS
To determine priority order of the protocol (IPv4/IPv6) to
be used for DNS query.
IPv4/IPv6*
FTP SYSLOG
To set whether to use the function to obtain various
system log files by FTP.
ON/OFF*
JOB SERIALIZE To set whether to use the connection serialize function.
ON/OFF*
BUFFER LIMIT
To clear the buffer acquisition limit of PSS.
ON/OFF*
E-RDS
E-RDS
SWITCH
To set whether to use the Embedded-RDS ON/OFF*
RGW-
ADDRESS
To check and set the server URL.
----
RGW-PORT To set the port number of the server.
1 to 443* to
65535
COM-TEST To execute the communication test.
Yes/No*
COM-LOG To display the detail of the communication
test result.
----
Items
Description
Setting Range
CLEAR
To clear the schedule information and alarm
alert filtering information besides the eRDS
setting value in service mode by executing
this item.
Yes/No*
CA-KEY
CLEAR
To change CA certificate to the default CA
certificate by executing this item and turning
ON and then OFF the power.
Yes/No*
MIB
CHARGECOUNT
To set Charge Counter MIB.
ALL ACCESS*
DISP ACCESS
NON ACCESS
TCP DELAYED
ACK
To set ACK delay function of TCP.
ON*/OFF
WOLtrans
To set recovery from sleep mode.
1: Wakeup in the new protocol (WSD) is enabled, and
there is no wakeup function in the old utility using the
CPCA Echo (broadcast) packet.
2: Wakeup in the new protocol (WSD) is enabled, and
there is no wakeup function in the old utility using the
SNMP search broadcast packet.
3: Wakeup in the old Canon utility is enabled, and there
is no wakeup function in the new protocol (WSD).
1* to 3
SLEEP
ADVERTISE
SWITCH
To set whether to use the sleep notification. ON*/OFF
PORT
To set the port number as the destination of
sleep notification.
1 to 11427* to
65535
TTL
To set the number of routers which can
exceed the number of sleep notification
messages
0 to 3* to 254
INTERVAL To set the notification interval (seconds) of
sleep notification.
60 to 600* to
65535
PROXYRES
To set the proxy response function by Yukon
ON*/OFF
Содержание Color imageRUNNER LBP5280
