Canon BS1 Скачать руководство пользователя страница 6 | Manualshive

Страница: 6 / 29

background image

0

0

Safety Precautions

Safety Precautions

0-2

0-2

Safety Precautions > Points to Note at Cleaning

Safety Precautions > Points to Note at Cleaning

Notes Before Servicing

Caution:

At servicing, be sure to turn off the power source according to the specified steps and
disconnect the power plug.

Caution:

Do not turn off the power switch when downloading is under way.
Turning off the main power switch while downloading is under way can disable the
machine.

Points to Note at Cleaning

Caution:

When performing cleaning using organic solvent such as alcohol, be sure to check that
the component of solvent is vaporized completely before assembling.

«
...
4
5
6
7
8
...
»

Содержание BS1






























Отзывы:

Нет отзывов

Похожие инструкции для BS1

Бренд: LAUMAS Страницы: 40

Бренд: A-Tach Mounts Страницы: 2

Бренд: A-Tach Mounts Страницы: 2

Бренд: A-Tach Mounts Страницы: 2

Бренд: AA Products Страницы: 8

Бренд: Zipp Страницы: 39

Бренд: Lantus Страницы: 5

Бренд: yasuni Страницы: 11

Oakville Series

Бренд: Napoleon Страницы: 72

Бренд: Napoleon Страницы: 4

Allure Vertical Series

Бренд: Napoleon Страницы: 120

Accel-a-Writer 8300

Бренд: Xante Страницы: 12

Бренд: Xantrex Страницы: 3

Бренд: Xerox Страницы: 15

Бренд: Xerox Страницы: 9

DocuPrint 180 NPS Series

Бренд: Xerox Страницы: 172

Бренд: Xerox Страницы: 11

Бренд: Xerox Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды