Canon 3622B002 Скачать руководство пользователя

Страница: 80 / 154

5-13

Chapter 5 Maintenance

Imprinter Ink Cartridge Replacement and Cleaning

When the optional imprinter is used, printing will become faint or nonexistent when the ink is depleted. It is recommended to keep
a spare ink cartridge on hand.

About the Imprinter

The ink cartridge for the imprinter that prints on scanned
documents is installed in the following location.

■

Preparing an Ink Cartridge

Use one of the following red, blue or green HP ink
cartridges. For details, contact your local authorized
Canon dealer or service representative.

Product Name: Ink Cartridge (Blue)
Product Code: 3693A002

Product Name: Ink Cartridge (Red)
Product Code: 3693A003

Product Name: Ink Cartridge (Green)
Product Code: 3693A004

Replacing Ink Cartridges

Replace the ink cartridge using the following procedure.

IMPORTANT

After replacing an ink cartridge, run a test print to confirm proper
printing.

(See “Imprinter Testing” on p. 5-17.)

Spread the document guides all the way to the left
and right.

With your finger, push in the area of the imprinter
cover shown by the arrow to release it.

The imprinter cover unlocks and opens to the front.

Содержание 3622B002



























































































































































Результаты поиска

Содержание 3622B002

Отзывы:

Похожие инструкции для 3622B002

Бренды по названию

Популярные бренды

Canon 3622B002, Руководство пользователя

Результаты поиска

Содержание 3622B002

Отзывы:

Похожие инструкции для 3622B002

Бренды по названию

Популярные бренды