background image

iii

Preface

Thank you for purchasing the Canon imageFORMULA DR-6050C/DR-7550C/DR-9050C Document Scanner. Please read this and the 
following manuals thoroughly before using the scanner to become acquainted with its capabilities and make the most of its many 
functions.
After reading the manuals, store them in a safe place for future reference.

Manuals for the Scanner

The documentation for the scanner consists of the 

Easy Start 

Guide

 and the 

Reference Guide

 (supplied with the scanner), 

the 

User Manual

 (this manual), and the 

CapturePerfect3.0 

Operation Guide

, which are provided in electronic form and 

registered in the menu during software installation.

Easy Start Guide

This manual describes the procedures for setting up the 
scanner for use. Please follow the procedures in the 

Easy 

Start Guide

 to set up the scanner.

Reference Guide

This manual consists of the basic scanner operating 
instructions extracted from the 

User Manual

.

User Manual (This Manual)

This manual consists of two sections: Hardware and 
Software. 
The Hardware section provides general information about 
the scanner operational settings, maintenance, and 
troubleshooting. 
The Software section describes how to use the ISIS/
TWAIN driver with the scanner, and how to set up job 
registration tools. 

CapturePerfect 3.0 Operation Guide 
(Electronic Manual)

This is the operation guide for CapturePerfect 3.0, the 
Canon document scanner application program. 

Hint

• The User Manual and the CapturePerfect 3.0 document files 

are installed in the following locations during software 
installation.

User Manual

CapturePerfect 3.0 Operation Guide

• Electronic versions of all manuals are available for viewing 

from the Setup CD. 

(See p. 2-5.)

Содержание 3622B002



























































































































































Отзывы: