manualshive.com logo in svg

Canon 2/3 Hole Puncher Unit-A1, Руководство по обслуживанию

Поделиться
Скачать
Canon 2/3 Hole Puncher Unit-A1 Скачать руководство пользователя страница 39

Power Supply

 Power Supply Route

The 24V and 5V are supplied to the puncher controller PCB through the finisher controller PCB when the host machine is turned
on.
The 5V is converted into 3.3V by the regulator IC (IC5) on the puncher controller PCB. The 24V is used to drive the motors and
the 5V is used to drive the sensors and the 3.3V is used to drive the logic.

Sensors

Sensors

Motor

Motor

5V

Finisher
Controller PCB

24V

Fuse

Fuse

(FU1)

(IC5)

Regulator IC

3.3V

Logic

(FU3)

Fuse

(FU2)

Puncher Controller PCB

(IC14)

5V

24V

Motor

Driver IC

24V

Puncher Relay PCB

5V

 Protection Function

The power input circuit of the puncher controller PCB is provided with a fuse which is blown when an excessive current flow. And
the 24V circuit for driving the motor is provided with the motor driver with an overcurrent protective function to protect from the
over current.

2. Technical Explanation

33

Содержание 2/3 Hole Puncher Unit-A1









































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды