manualshive.com logo in svg

Canon 2/3 Hole Puncher Unit-A1, Руководство по обслуживанию

Поделиться
Скачать
Canon 2/3 Hole Puncher Unit-A1 Скачать руководство пользователя страница 38

Jam Detection

 Outline

The puncher unit is equipped with the following sensors to detect the jam at the punch operation.

• Punch HP Sensor 1 (PS303)
• Punch HP Sensor 2 (PS304)

PS304

PS303

 Jams

The conditions for detecting whether a jam has occurred are stored in the puncher controller PCB in advance. A jam is determined
by detection states of the sensors at the check timing.
When the puncher controller PCB determines that a jam has occurred, it stops feeding/delivering paper and notifies the host
machine.

Jam type

Sensor

Jam description

Punch jam

PS303
PS304

When the punch HP sensor 1 (PS303) and punch HP sensor 2 (PS304) cannot
detect the home position of the punch again, even when the specified time
elapses after the sensors have detected the home position during the punch
operation.

Error avoidance jam

-

When any of the following errors is detected during feeding operation.

• Punch motor (E590)
• Punch shift motor (E593)

2. Technical Explanation

32

Содержание 2/3 Hole Puncher Unit-A1









































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды