Canon 1730, Руководство по обслуживанию

Страница: 241 / 358

7
7
7-7
7-7
Error Code > Error Code > Error Code Details
Error Code > Error Code > Error Code Details
Ecode
Detail
Code
Item Description
E537 8001 Title Rear Alignment Motor (M5) error
Description At initialization of the Rear Alignment Plate, the Rear Alignment Plate
failed to move from the Rear Alignment Plate HP Sensor (S5) although
the Rear Alignment Motor (M5) was driven for 10 mm.
Remedy 1. Check the connector connection of the Rear Alignment Plate HP
Sensor (S5) or the Rear Alignment Motor (M5).
2. Check for open circuit of the Harness of the Rear Alignment Plate HP
Sensor (S5) or the Rear Alignment Motor (M5).
3. Replace the Rear Alignment Plate HP Sensor (S5).
4. Replace the Rear Alignment Motor (M5).
5. Replace the Finisher Controller PCB.
E537 8002 Title Rear Alignment Motor (M5) error
Description At initialization of the Rear Alignment Plate, the Rear Alignment Plate
failed to be detected by the Rear Alignment Plate HP Sensor (S5)
although the Rear Alignment Motor (M5) was driven for 0.78sec.
Remedy 1. Check the connector connection of the Rear Alignment Plate HP
Sensor (S5) or the Rear Alignment Motor (M5).
2. Check for open circuit of the Harness of the Rear Alignment Plate HP
Sensor (S5) or the Rear Alignment Motor (M5).
3. Replace the Rear Alignment Plate HP Sensor (S5).
4. Replace the Rear Alignment Motor (M5).
5. Replace the Finisher Controller PCB.
E540 8001 Title Stack Tray Shift Motor (M8) error
Description The Stack Tray Shift Motor (M8) was driven for 4 seconds, but the Stack
Tray shifting operation could not be completed.
Remedy 1. Check the connector connection of the Stack Tray Paper Height
Sensor (S9) or the Stack Tray Shift Motor (M8).
2. Check for open circuit of the Harness of the Stack Tray Paper Height
Sensor (S9) or the Stack Tray Shift Motor (M8).
3. Replace the Stack Tray Paper Height Sensor (S9).
4. Replace the Stack Tray Shift Motor (M8).
5. Replace the Finisher Controller PCB.
E575 8002 Title Gripper Motor (M7) error
Description The gripper unit does not leave the gripper unit home position when the
Gripper Motor (M7) has been driven for 3.8 seconds.
Remedy 1. Check the connector connection of the Gripper HP Sensor (S7) or
the Gripper Motor (M7).
2. Check for open circuit of the Harness of the Gripper HP Sensor (S7)
or the Gripper Motor (M7).
3. Replace the Gripper HP Sensor (S7).
4. Replace the Gripper Motor (M7).
5. Replace the Finisher Controller PCB.
Ecode
Detail
Code
Item Description
E575 8004 Title Gripper Motor (M7) clock error
Description When the Gripper Motor (M7) was operated, the Gripper Encoder
Sensor (S8) detected rotation of 400 clocks or more.
Remedy 1. Check the connector connection of the Gripper Encoder Sensor (S8)
or the Gripper Motor (M7).
2. Check for open circuit of the Harness of the Gripper Encoder Sensor
(S8) or the Gripper Motor (M7).
3. Replace the Gripper Encoder Sensor (S8).
4. Replace the Gripper Motor (M7).
5. Replace the Finisher Controller PCB.
E577 8001 Title Paddle Motor (M3) error
Description Although the Paddle Motor (M3) was driven for 175 steps, the Paddle
failed to move from the Paddle HP Sensor (S3).
Remedy 1. Check the connector connection of the Paddle HP Sensor (S3) or the
Paddle Motor (M3).
2. Check for open circuit of the Harness of the Paddle HP Sensor (S3)
or the Paddle Motor (M3).
3. Replace the Paddle HP Sensor (S3).
4. Replace the Paddle Motor (M3).
5. Replace the Finisher Controller PCB.
E577 8002 Title Paddle Motor (M3) error
Description The Paddle Motor (M3) was driven for 2 seconds, but the Paddle could
not be detected by the Paddle HP Sensor (S3).
Remedy 1. Check the connector connection of the Paddle HP Sensor (S3) or the
Paddle Motor (M3).
2. Check for open circuit of the Harness of the Paddle HP Sensor (S3)
or the Paddle Motor (M3).
3. Replace the Paddle HP Sensor (S3).
4. Replace the Paddle Motor (M3).
5. Replace the Finisher Controller PCB.
E583 8001 Title Tray Auxiliary Guide Motor (M6) error
Description The Tray Auxiliary Guide Motor (M6) was driven for 30 mm, but the Tray
Auxiliary Guide failed to move from the Tray Auxiliary Guide HP Sensor
(S6).
Remedy 1. Check the connector connection of the Tray Auxiliary Guide HP
Sensor (S6) or the Tray Auxiliary Guide Motor (M6).
2. Check for open circuit of the Harness of the Tray Auxiliary Guide HP
Sensor (S6) or the Tray Auxiliary Guide Motor (M6).
3. Replace the Tray Auxiliary Guide HP Sensor (S6).
4. Replace the Tray Auxiliary Guide Motor (M6).
5. Replace the Finisher Controller PCB.