CN24
H4
Ceramic heater, provides sealing heat for No.4 heater assembly set.
CN25
H5
Ceramic heater, provides sealing heat for No.5 heater assembly set.
CN26
MC
DC motor, cam driver.
CN27
MP
DC motor, compressor driver.
CN28
BK
Magnetic brake,, lock ball screw for strapping.
CN29
MH
DC motor, upper sealing driver.
CN30
MSX
Micro switch, check rear edge of banknotes.
CN31
POWER DC 24V power supply.
KH1
Adjust temperature of No.1 heater assembly set.
1. Short pin 1 and pin 2: Increase temperature of No.1 heating plate.
2. Short pin 2 and pin 3: Decrease temperature of No.1 heating plate.
KH2
Adjust temperature of No.2 heater assembly set.
1. Short pin 1 and pin 2: Increase temperature of No.2 heating plate.
2. Short pin 2 and pin 3: Decrease temperature of No.2 heating plate.
KH3
Adjust temperature of No.3 heater assembly set.
1. Short pin 1 and pin 2: Increase temperature of No.3 heating plate.
2. Short pin 2 and pin 3: Decrease temperature of No.3 heating plate.
KH4
Adjust temperature of No.4 heater assembly set.
1. Short pin 1 and pin 2: Increase temperature of No.4 heating plate.
2. Short pin 2 and pin 3: Decrease temperature of No.4 heating plate.
KH5
Adjust temperature of No.5 heater assembly set.
1. Short pin 1 and pin 2: Increase temperature of No.5 heating plate.
2. Short pin 2 and pin 3: Decrease temperature of No.5 heating plate.
KL1
Adjust MF 1 tape supply length.
1. Short pin 1 and pin 2: Increase tape supply length.
2. Short pin 2 and pin 3: Decrease tape supply length.
KL2
Adjust MF 2 tape supply length.
1. Short pin 1 and pin 2: Increase tape supply length.
2. Short pin 2 and pin 3: Decrease tape supply length.
KL3
Adjust MF 3 tape supply length.
1. Short pin 1 and pin 2: Increase tape supply length.
2. Short pin 2 and pin 3: Decrease tape supply length.
KMP
MP test.
1. Short pin 1 and pin 2: Reverse rotation to release banknotes.
2. Short pin 2 and pin 3: Forward rotation to press banknotes.
KMH
MH Test.
Short pin 1 and pin 2: No.4 and No.5 heater assembly sets return to
original position.
Short pin 2 and pin 3: No.4 and No.5 heater assembly sets move to
sealing position.
KCX
MC test.
Short two pins once, cam will rotate to next angle, total 3 angles
including original angle.
– 13 –
Содержание S-35
