Can-Am Spyder RT Limited SE6 Скачать руководство пользователя страница 45

Страница: 45 / 52

SETUP

CE Models (High Beam)

rbl2014-004-019_b

LH SIDE SHOWN

1. High beam adjustment knob

HEADLIGHT BEAM ADJUSTMENT

Raise beam

Turn knob clockwise

Lower beam

Turn knob counterclockwise

3. Install both middle side panels.

Low Beam Headlight Units (CE Models)

1. Remove both middle side panels.

2. To adjust headlight beam, turn the adjustment

knob. Adjust both headlights evenly.

rbl2014-004-019_c

LH SIDE SHOWN

1. Adjustment knob "LB"

3. Install both middle side panels.

Headlights Horizontal Aiming Adjustment,
High Beams (Japan Models Only)

If high beam headlights are out of adjustment (to
far left or right), carry out the following procedure.

1. Remove both middle side panels.

2. To adjust headlight beam, turn the adjustment

knob.

rbl2014-004-054_a

LH SIDE SHOWN

1. High Beam Horizontal Adjustment Knob
2. High Beam Vertical Adjustment Knob "HB"
3. Low Beam Vertical Adjustment Knob "LB"

Adjust both high beam headlights so that a line
drawn from the center of the focus point (bright-
est spot on the wall) to the center of the headlight
assembly is parallel to the fore and aft center line
of the vehicle.

A B

rbl2014-004-069_a

TYPICAL - HIGH BEAM HEADLIGHT REFLECTION ON TEST
SURFACE

1. Ground
2. Focus point
3. Vehicle center line

A. 800 mm (31-1/2 in) above ground
B. 850 mm (33-1/2 in) above ground
C. 122 mm (4-13/16 in) from vehicle center line

Storage Compartment Covers

Front Storage Compartment Cover

1. Open front storage compartment cover then let

it fall.

PREDELIVERY

2014-1

45 / 52

Содержание Spyder RT Limited SE6





















































Результаты поиска

Содержание Spyder RT Limited SE6

Отзывы:

Похожие инструкции для Spyder RT Limited SE6

Бренды по названию

Популярные бренды

Can-Am Spyder RT Limited SE6, Инструкция по эксплуатации

Результаты поиска

Содержание Spyder RT Limited SE6

Отзывы:

Похожие инструкции для Spyder RT Limited SE6

Бренды по названию

Популярные бренды