6
Cleaning and Maintenance
1. Turn off the power button (3), unplug it and clean the device after completely cooling.
2. Always empty the water tank (9) after use. From time to time, clean the water tank (9) with a damp sponge or cloth.
3. Detach the filter (18) and remove used coffee from the Filter. If the Filter holes are clogged with coffee, use a brush to clean it. You can
unscrew the coffee funnel (20) and clean the coffee grounds in the filter housing (17).
4. The cups, water tank (9), drip grid (6), removable drip tray (7), filter (15+16+17+18+20) may be washed in water with some mild
detergent without abrasive substances or solvents. External parts should be cleaned with a soft cloth or sponge. Highly abrasive
cleaners or brushes may cause surface scratches.
Note: Do not use alcohol or solvent cleaner and do not immerse the machine in water to clean.
DECALCIFICATION
If coffee brewing takes longer time than in the beginning of use or the steam nozzle (13) does not produce steam, the appliance should
be decalcified. If hard water is used, the appliance should be decalcified after it has been used approximately 40 times. If soft water is
used the machine can be decalcified after it has been used approximately 80 times. Espresso machine liquid decalcifier may be used for
decalcifying the appliance. Before decalcifying, make sure that the device is disconnected from the power supply.
1) Pour approximately 250 ml of lukewarm water and then add 250 ml of espresso machine liquid decalcifier.
2) Place the filter (15+16+17+18+20) in locked position into the device. Then place a cup half-filled with cold water under the steam
nozzle (13) and an empty cup under the filter funnel (20).
3) Connect the device to the power supply.
4) Press the power button (3).
5)Then press the Auto Single Cup button (1).
6) When the decalcifier starts to flow down into an empty cup, insert the tip of the steam nozzle (13) into a cup filled with cold water and
press the steam button (5).
7) Wait for a few seconds and switch off the device. After decalcifying, the device must be rinsed three times with clean water. In order to
do it, repeat steps 1 to 7 filling the water tank (9) with clean water only.
Troubleshooting
Symptom: No water / no steam
Reason 1: Whether the water tank (9) has got water inside / is in place?
Solution 1: Add water to the tank (9).
Reason 2: No water is added in advance in the machine.
Solution 2: Method of water adding: press the Manual Coffee Cup button (4), the pump starts pumping water into the device, press
Manual Coffee Cup button (4) after few seconds.
Reason 3: The machine does not complete preheating.
Solution 3: Wait. The machine can make coffee after the warm-up is completed. Warm-up is completed when the light indicator (19)
changes from blue flashing to always being on blue.
Symptom: No steam
Reason 1: Steam hole blocked
Solution 1: Use a small wire to poke the small hole in the bottom of the steam nozzle (13), clean it this way.
Solution 2. After the milk foam is finished, do a hot water function to clean the steam tube.
Symptom: Bad milk foam
Reason 1: Is it whole milk?
Solution 1: Use whole milk.
Symptom: Bad milk foam
Reason 1: The steam button (5) starts to froth milk foam before the device is warmed up completely.
Solution 1: Wait. Start steaming after the light indicator (19) changes color from red flashing to continuous red.
TECHNICAL DATA:
Capacity max: 1.6 liters
Voltage: 220-240V ~50/60Hz
Power: 850W
Power Max: 1000W
Pressure: 15 Bars
Please transfer cardboard packaging to waste paper. Pour the polyethylene bags (PE) into the plastic container
Worn device should be returned to the appropriate point
storage because it is dangerous in the device
ingredients may pose a threat to the environment.
The electrical device should be handed over to limit
its reuse and use. If in the device
there are batteries you have to take out and give to the point
stored separately.
Содержание Premium CR 4410
Страница 2: ...2 21 20 23 19 1 5 4 3 2 22 10 24 ...
