7
4.Plug in 220-240V~ 50/60 Hz outlet. The unit will beep and all the indicator will lights for one second.
If no operation within 15 seconds, it will back to power off status.
The operation is the same for both left and right heating plates.
When the programmed time has elapsed, the induction cooker will beep once and shut off automatically.
The child lock can be used when the heating plate heating or is on standby.
The icons (12) on the left and right heating plates display will light up together.
The whole device power button (1) is on the left heating plate.
There are total 10 temperature levels for your choice: 60
℃
, 80
℃
,100
℃
120
℃
,140
℃
160
℃
, 180
℃
, 200
℃
, 220
℃
, 240
℃
, of the
pot’s bottom.
5.Child lock button.
2. Press the option button (2), the display window (7) shows the default power “1400” and the heating will start. Press the “+”/ “-“
buttons (3/4) to select desired power level: “+” button (4) to increase and “-” button (3) to decrease the power. There are total 9 power
levels for your choice: 200W,500W,800W,1000W,1200W,1400W,1600W, 1800W, 2000W.
Do not use petrol, solvents, brushes or pastes to clean the induction heating plate.
Wipe the appliance with a damp cloth with some dishwashing liquid. Use a vacuum cleaner to remove dirt from the air supply and fan
grilles. Clean the glass surface and the control panel with a soft damp cloth and gentle cleaners for glass surfaces.
Only child lock button and power button (1) are available when the child lock is activated.
Make sure that water does not drip on the cooker, as this can cause damage. Never immerse the appliance or the cable in water.
Press and hold ”+” (3) and ”-” (4) together for 3 seconds will enter into child lock, the icon on the display will light up (8).
Washing the appliance after each use is recommended. Disconnect the appliance from the mains socket and wait until it cools down.
3. Press the option button (2) again to switch to the temperature mode. The indicator
℃
(11) will light up. The display window (7)
shows the default temperature 200
℃
. Press the “+”/ “-“ buttons (3/4) to select desired temperature level: “+” button (4) to increase and
“-” button (3) to decrease the temperature.
All servicing, other than cleaning, should be performed by an authorized service representative.
Technical data:
1. Press the power button (1) on the left heating plates.
4. If you wish to use the timer, press the option button (2) the display window (7) shows the default power “1400” and start heating.
Press the “+”/ “-“ buttons (3/4) to select desired power level: “+” button (4) to increase and “-” button (4) to decrease the power after that
press the timer button (5).The display window (7) shows the default time “0:00”. Press the “+”/ “-“ buttons to select cooking time in range
0-3 hours, “+” (4) button to increase and “-”(3) button to decrease the time. If you press and hold “+” or ”-“ button, the time will change
faster. Once desired time is selected, press timer button (5) again or wait 5 seconds then timer is now activated. Display window (7) will
show the timer or power (if in temperature mode will show the timer or temperature) alternately.
Press and hold the ”+” (3) and ”-”(4) together for 3 seconds to cancel the child lock function.
CLEANING AND MAINTENANCE
NOTE: If at any time during the cooking cycle you would like to cancel the timer, simply press the timer button (5).
6.Press the power button (1) on the left side device, to turn the unit off when finished cooking.
Power: 3500W
means that the housing parts become much hotter when the appliance is in use.
BE CAREFUL!!!
I
Power supply: 220-240V ~50/60Hz
Attention! Hot Surface” – Temperature of accessible surfaces can be higher when the appliance is operating, which
Please transfer cardboard packaging to waste paper. Pour the polyethylene bags (PE) into the plastic container
Worn device should be returned to the appropriate point
storage because it is dangerous in the device
ingredients may pose a threat to the environment.
The electrical device should be handed over to limit
its reuse and use. If in the device
there are batteries you have to take out and give to the point
stored separately.
