Campbell TDR200 Скачать руководство пользователя страница 34

Страница: 34 / 53

A-1

Appendix A. SDMX50-Series

Multiplexers

A.1 General

Prior to the SDM8X50, the SDMX50 series multiplexers were used with the

TDR100 to measure multiple sensors. SDMX50 series multiplexers are also

compatible with the TDR200. The SDMX50SP was identical to the SDM8X50

in form, fit, and function. The SDMX50 came with the multiplexer mounted in

a 10-inch x 12-inch enclosure, similar to the SDM8X50-E. The SDMX50LP

included the backplate and multiplexer found in the SDMX50 but shipped

without an enclosure.

SDMX50 multiplexers may be used interchangeably with SDM8X50

multiplexers. The major difference between them is that the SDM8X50 uses

hermetically sealed, longer lasting electromechanical relays and provides better

surge protection than the SDMX50 series.

A.2 Specifications

A.2.1 Physical

Consists of

Size

When Used

SDMX50 50

Ohm Coaxial

Multiplexer

with

Enclosure

Multiplexer

circuit board

mounted in an

environmental

enclosure with a

strain relief

backplate.
Enclosure

includes a

bracket for

mounting to a

tripod, tower, or

a 1.0 in. to 1.25

in. IPS Schedule

40 pipe.

Weight: 4.4 kg

(9.8 lb)
Enclosure

Outside

Dimensions with

Mounts: 40.4 x

29.2 x 17.5 cm

(15.9 x 11.5 x

6.9 in)
Enclosure Inside

Dimensions:
25.4 x 30.4 x

12.7 cm

(10 x 12 x 5 in)

When the

multiplexer will

be housed in its

own enclosure

without the

datalogger and

power supply.

SDMX50LP

50 Ohm

Multiplexer

with 10 in. x

12 in.

Backplate

Multiplexer

circuit board

attached to one

end of a strain

relief backplate.

Circuit Board

Dimensions:

24.9 x 12.2 x

4.6 cm (9.8 x

4.8 x 1.8 in)
Strain Relief

Backplate

Dimensions
26.7 x 27.9 x 1.3

cm (10.5 x 11 x

0.5 in)

When a user-

supplied

enclosure will

house only the

multiplexer

without the

datalogger and

power supply.

Содержание TDR200






















































Результаты поиска

Содержание TDR200

Отзывы:

Бренды по названию

Популярные бренды

Campbell TDR200, Инструкция по эксплуатации

Результаты поиска

Содержание TDR200

Отзывы:

Бренды по названию

Популярные бренды