Campbell NL241 Скачать руководство пользователя страница 44

Страница: 44 / 76

FIGURE 9-1. Working around firewalls

9.1 Configuring the NL241

Connect to the NL241 in

Device Configuration Utility

(see

Configuring the NL241

(p. 20)).

1. On the NL241 tab:

a. Set Bridge Mode to disable.

b. Set DHCP Enabled to disable.

c. Enter the IP Address, Network Mask, and Default Gateway. These values can be

provided by your network administrator.

2. On the Network Services tab, make note of the PakBus/TCP Service Port.

9.2 Configure the data logger

NOTE:
The data logger must first be configured for internet communications (that is, through an
NL115, an NL120, a second NL241, or a cellular modem).

1. Connect a serial cable from the computer COM port to the data logger RS-232 port.

2. Open

Device Configuration Utility

. Select the device type of the data logger (CR800,

CR1000, or CR3000), the appropriate Communication Port, and Baud Rate. Click Connect to
connect to the data logger.

3. On the Network Services tab:

Under PakBus TCP Clients, input the NL241 IP address and PakBus TCP Service Port.

4. Click Apply to save the changes and then close

Device Configuration Utility

NL241 Wireless Network Link Interface

Содержание NL241












































































Результаты поиска

Содержание NL241

Отзывы:

Похожие инструкции для NL241

Бренды по названию

Популярные бренды

Campbell NL241, Руководство по эксплуатации продукта

Результаты поиска

Содержание NL241

Отзывы:

Похожие инструкции для NL241

Бренды по названию

Популярные бренды