Use and Maintenance Manual – Original
Instructions Rev.: 00, Date 19/03/2021
Pag. 19
2.1 Precautions
WARNING!
The Manufacturer declines all responsibilities if the precautions below are not taken.
The accomplishments concerning working environment safety and health regulations indicated by the current
laws (2003/10/CE Directive, 2002/44/CE Directive and 81/2008 Law Decree) have to be carried out either by the end-
user or by the employer: supplying the adequate individual protecting devices, informing about working risks,
performing sanitary survey, etc…
The over-exposure to the vibrations may cause neurovascular lesions to people suffering from circulatory disor-
ders. In case of symptoms which could be referred to, such as an over-exposure, a specialist has to be contacted.
These symptoms can be torpor, loss of sensitivity, sharp pains, itch, strength reduction or loss, complexion dis-
coloration or structural modifications. This usually happens in one’s hands, wrists and fingers
.
2.1.1 Results of the tests carried out according to the Laws
WARNING!
Risks due to the operator’s contact with the tool and/or machine noise and vibrations
.
1. SOUND LEVEL:
Continuous A-weighted sound pressure level at the operator’s ear (LpA), and sound power
level of the tool (LwA), both calculated according to the UNI EN ISO 3744
:
LpAeq = 73 dBA - LwA = 82 dBA
2. VIBRATIONS LEVEL:
Average weighted hand-transmitted vibration value in frequency, the operator is exposed
to, measured in compliance with EN ISO 5349-2:
•
vibration level
a
heq
= 6,35 m/
s
3. ELECTROMAGNETIC COMPABILITY LEVEL
The equipment complies with the 2014/30/UE Directive and the following modifications.
2.2 General precautions
WARNING!
Do not use the tool indoor or in a potentially explosive environment.
WARNING!
•
The tool has been designed for a professional use.
•
Use the tool only with the accessories indicated by the Manufacturer.
•
Use the tool only from the ground, working in a stable and safe position.
•
Always use adequate clothing as called for by the job. Wear protective goggles and verify that your clothes are fitting to
the body. Do not wear ties, necklaces or belts or keep loose long hair which may get caught in the moving parts. Use
anti-sliding shoes and anti-perforation gloves.
•
Wear a noise-abatement headset.
•
Do not operate, service or repair the tool if you are under the influence of medicines, alcohol or drugs which could impair
your alertness or co-ordination.
•
Only well trained and qualified personnel - who have read the use and maintenance manual carefully - are allowed to
use the tool. The safety course must be administered by the employer.
•
Entrust or lend the tool only to people who are familiar with the instructions for use or trained by personnel authorized
by the employer.
•
Keep the tool out of the reach of children, as well as of people with disabilities or untrained in its use and keep it away
from animals.
•
The operator is the only responsible for injuries caused to other people or for damages caused to their belongings.
•
Do not use the tool when you are in an unstable position or off balance, on slipping surfaces (i.e. hills and/or wet grass)
or wherever there is no possibility of maintaining a stable balance (i.e. steep slopes).
•
Never use the tool while standing on a ladder.
•
Before any routine maintenance operations, read the Use and Maintenance Manual carefully. For any maintenance
operation which is not indicated in this manual, please contact one of the Service Points authorized by the Manufacturer.
•
Use the tool just for the purposes described in par. “Product description”. Any other use may cause injuries.
•
Remove the battery (13) before any maintenance operation.
•
Keep this manual with care and read it before any tool use.
•
Keep all the danger and safety indications stickers in perfect conditions.
•
Do not use petrol, solvents or other aggressive products to clean the tool.
•
Avoid working in bad weather conditions, such as in case of fog, rain, strong wind, hail storm, snow or ice.
•
Содержание STARBERRY MD2
Страница 2: ......
