manualshive.com logo in svg

Camfil CamSafe, Инструкция по установке и эксплуатации

Поделиться
Скачать
Camfil CamSafe Скачать руководство пользователя страница 8

 

EMC_SPEC018_C2.doc 

Rev. D 

–

 2020 05 19 

8/44 

 

Install & Operating Manual 

CamSafe

 

 

 

Temperature Limitations 
 

From the technical characteristics of materials employed (paint & plastic parts), it is safe to say that 
CamSafe housings are fully functional for the same temperature range as the most common filter cell 
ranges, i.e. 60°C maximum for continuous use. 

PLEASE NOTE:

 

HOT process air and/or environment 

   

 

Under no circumstances should a housing be continuously exposed to  

   

 

temperatures > 90°C. 

PLEASE NOTE:

 

COLD process air 

   

 

Process air temperatures <4°C would require an insulated housing to avoid  

   

 

condensation. 

   

 

This option is NOT available ytd due to the morphology of the housing body. 

 
The following materials are used in CamSafe filter housings. 

➔

 

Max. temperatures are values for permanent exposure.  

 

Illustration 

Name 

 

Material(s) 

 

Temp. 

Max 

[°C]

 

 

Housing Body & Door 

 

Weldment 

Housing body & door 

(a) 1.0038 (S235JRG2)  

(b) SS 1.4301 (X5CrNi18-10) 

(c) SS 1.4404 (X5CrNiMo17-12-2) 

( >250 ) 

- 

Screws & Nuts & Fittings 

(a) Zn8C 

(b) SS A2 

(c) SS A4 

( >250 ) 

- 

Powder Coat 

Primer 

Topcoat 

 

Epoxy 

Polyester 

( 

<=90 

)

 

- 

Door Gasket 

Chloropren Rubber 40 Shore A 

( 

<=100 

) 

- 

Door Gasket Tape 

Acrylic Adhesive 

( 

<=120 

) 

 

Star Button 

DIN 6336-KU-63-M10-K-MS 

Phenolic Resin 

PF31 

( 

<=140

 ) 

-

 

Stickers 

PVC 

( 

<=60 

) 

 

 

 

 

Содержание CamSafe













































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды