manualshive.com logo in svg

Camfil CamSafe, Инструкция по установке и эксплуатации

Поделиться
Скачать
Camfil CamSafe Скачать руководство пользователя страница 18

 

EMC_SPEC018_C2.doc 

Rev. D 

–

 2020 05 19 

18/44 

 

Install & Operating Manual 

CamSafe

 

 

8.5

 

Installation of Wall-mounted Configurations 
 

Wall-mounted configurations are designed with a wall-flange, allowing airtight installation in a 
technical area with filter access from the room.  
Wall-mounted configurations can be installed module-by-module or as a completed tower. 
 

PLEASE NOTE:

 

Access to both sides of the wall is required for the installation. 

Precautions : 

Wall-mounted configurations are typically front-heavy. They may be unstable  

   

 

and prone to tipping over under lateral forces during manipulation / transport! 

   

 

Consult the project drawing for dimensions,  overall weight and position  

   

 

of the center of gravity  before manipulating the tower!  

   

 

 

 

The center of gravity will usually remain within the perimeter 
of the support legs. Once installed, the wall flange and it's 
attachment points have no weight bearing function! 
Their only purpose is to provide a sealing surface between 
cleanroom and technical area. 

Adequate anchor- & gasket solutions will depend on the 
wall technology and are to be defined with the installation 
contractor. 

For both installation as a tower or module-by-module, the 
following priorities should be observed : 

1.

 

Alignment and Airtight assembly of modules (safety critical) 

2.

 

Solid attachment to the ground 

3.

 

Attachment to the wall, including appropriate sealing measures 

 

 

 

 

Содержание CamSafe













































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды