manualshive.com logo in svg

Camfil CamSafe, Инструкция по установке и эксплуатации

Поделиться
Скачать
Camfil CamSafe Скачать руководство пользователя страница 15

 

EMC_SPEC018_C2.doc 

Rev. D 

–

 2020 05 19 

15/44 

 

Install & Operating Manual 

CamSafe

 

 

8.2

 

Assembly of Horizontal Airflow Configurations 
 

Subject to order conditions and/or transport limitations, components of most larger horizontal-flow 
configurations may be shipped separately. 

Airtight assembly is required, instruction for module / gasket assembly from General Assembly 

§ 8.1

 

fully apply. 

 

Precautions : 

Horizontal flow involves temporarily cantilevered modules during assembly. 

   

 

Configurations may reach important height. 

   

 

Consult drawings for dimensions, weight and centers of gravity. 

   

 

Prepare wooden or plastic shims for temporary alignment support.  

   

 

Respect applicable work safety rules for access, manipulation and static support.

 

 

 

 

 

 

 

 

Place 1

st

 collector 

on the support stand. 

 

Position collector 

and secure against tipping over.

 

 

For non-adhesive gaskets, place 

small strips of double-sided tape 

on the collector flange(s). 

 

 

 

 

 

 

 

Place gasket(s) on the flange(s), 

aligning flange and gasket holes. 

 

Place 1

st

 housing,  

aligning flange holes.  

 

Use housing-collector bolts to 

securely link to the support stand. 

Tighten nuts, do not block yet 

at this point. 

 

 

 

 

13

 

M8

 

Содержание CamSafe













































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды