background image

4

DMX

IT

ALIANO

POLSKI

ESP
AÑOL

FRANCAIS

DEUTSCH

ENGLISH

33. Dust and other debris within the device may damage it. The device should be serviced or cleaned regularly by qualified specialists 

depending on the environmental conditions (dust, nicotine, smoke, etc.) in order to avoid overheating.

34. The distance to combustible materials must be at least 0.5 m.

35. Power cables for powering multiple devices must have a core cross-section of at least 1.5 mm². In the EU, lines must be H05VV-F or 

similar. Adam Hall provides suitable cables. Using these cables, you can connect multiple devices via the Power Out connection with the 

Power In connection of another device. Ensure that the total power consumption of all connected devices does not exceed the specified 

value (printed on the device). Be sure to keep power lines as short as possible.

36. The appliance is not to be used by persons (including children) with reduced physical, sensory or mental capabilities, or lack of 

experience and knowledge.

37. Children must be instructed not to play with the device.

38. If the power cord of the device is damaged, do not use the device. The power cord must be replaced by an adequate cable or assembly 

from an authorized service center.

CAUTION:

To reduce the risk of electric shock, do not remove cover (or back). There are no user serviceable 

parts inside. Maintenance and repairs should be exclusively carried out by qualified service 

personnel.

The warning triangle with lightning symbol indicates dangerous uninsulated voltage inside the unit, which may cause an 

electrical shock.

The warning triangle with exclamation mark indicates important operating and maintenance instructions.

Warning! This symbol indicates a hot surface. Certain parts of the housing can become hot during operation. After use, wait 

for a cool-down period of at least 10 minutes before handling or transporting the device.

Warning! This device is designed for use below 2000 metres in altitude.

Warning! This product is not intended for use in tropical climates.

Caution! Intense LED light source! Risk of eye damage. Do not look into the light source.

CAUTION! IMPORTANT INFORMATION ABOUT LIGHTING PRODUCTS!

1.  Do not stare, even temporarily, directly into the light beam.

2.  Do not look at the beam directly with optical instruments such as magnifiers.

3.  Stroboscope effects may cause epileptic seizures in sensitive people! People with epilepsy should definitely avoid places where  

strobes are used.

SIGNAL TRANSMISSION VIA RADIO (E.G., W-DMX OR WIRELESS AUDIO SYSTEMS): 

The quality and performance of wireless signal transmission is generally dependent on the ambient conditions. 

The following variables, for example, have an influence on the range and signal stability: 

• Shielding (e.g., masonry, metal structures, water) 

• High radio frequency (e.g., strong WI-FI networks) 

• Interference 

• Electromagnetic radiation (e.g., LED video walls) 

All range specifications refer to free-field application with visual contact between transmitter and receiver without interference!

Содержание OPUS X WASH





















Отзывы: