CAME BX Series, Руководство по установке

Страница: 31 / 112

p.
3
- M
anu
al
FA
0
0
9
4
5
-E
N
- 0
1/
2
0
18 - © C
A
M
E S
.p
.A
. - T
ransla
te
d o
riginal inst
ru
ct
io
ns
Danger of high voltage.
Danger of crushing.
Danger of foot crushing.
Danger of hand entrapment.
Do not transit through during maneuvering.
GENERAL PRECAUTIONS FOR INSTALLERS
⚠ WARNING! Important safety instructions.
Follow all of these instructions. Improper installation can cause serious bodily harm.
Before continuing, also read the general precautions for users.
This product must only be used for its specifi cally intended purpose. any other use may be hazardous. Came S.p.A. is not liable for any damage
caused by improper, wrongful and unreasonable use. • This manual's product is defi ned by machinery directive 2006/42/CE as "partly-completed
machinery". Partly-completed machinery is a set that almost constitutes a machine, but which, alone, cannot ensure a clearly defi ned application.
Partly-completed machinery must only be incorporated or assembled to other machinery or other partly-completed machinery or apparatuses to build
machinery that is regulated by Directive 2006/42/CE. The fi nalized installation must comply with European Directive 2006/42/CE and with currently
applicable European standards. • Given these considerations, all procedures stated in this manual must be exclusively performed by expert, qualifi ed
staff • The manufacturer declines any liability for using non-original products; which would result in warranty loss • Keep this manual inside the
technical folder along with the manuals of all the other devices used for your automation system. • Make sure the temperature range shown on the
product is suitable for the climate where it will be installed • Laying the cables, installation and testing must follow state-of-the-art procedures as
dictated by regulations • If the power-supply cable is damaged, it must be immediately replaced by the manufacturer or by an authorized technical
assistance center, or in any case, by qualifi ed staff , to prevent any risk • During all phases of the installation make sure you have cut off the mains
power source. • The operator cannot be used with gates fi tted with pedestrian doors, unless its operation can be activated only when the pedestrian
door is in safety position. • Make sure that people are not entrapped between the gate's moving and fi xed parts due to the gate's movement. Before
installing the operator, check that the gate is in proper mechanical condition, that it is properly balanced and that it properly closes: if any of these
conditions are not met, do not continue before having met all safety requirements. • Make sure the gate is stable and the castors function properly
and are well-greased, and that it opens and closes smoothly. • The guide rail must be well-fastened to the ground, entirely above the surface and
free of any impediments to the gate's movement. • The rails of the upper guide must not cause any friction. • Make sure that opening and closing
limiters are fi tted • Make sure the operator is installed onto a sturdy surface that is protected from any collisions • Make sure that mechanical stops
are already installed • If the operator is installed lower than 2.5 from the ground or from any other access level, fi t any protections and signs to prevent
hazardous situations. • Do not fi t the operator upside down or onto elements that could yield to its weight. If necessary, add reinforcements to the
fastening points • Do not install door or gate leaves on tilted surfaces • Check that no lawn watering devices spray the operator with water from the
bottom up. • Any residual risks must be indicated clearly with proper signage affi xed in visible areas. All of which must be explained to end users. •
Suitably section off and demarcate the entire installation site to prevent unauthorized persons from entering the area, especially minors and children.
• Affi x cautionary signs, such as the door plate, the gate plate, wherever needed and in plain sight. • Use proper protections to prevent mechanical
hazards when people are loitering around the machinery's range of action, for example to prevent fi nger crushing between the rack and pinion) • The
electrical cables must run through the cable glands and must not touch any heated parts, such as the motor, transformer, and so on) • Make sure
you have set up a suitable dual pole cut off device along the power supply that is compliant with the installation rules. It should completely cut off the
power supply according to category III surcharge conditions • All opening controls must be installed at least 1.85 m from the perimeter of the gate's
working area, or where they cannot be reached from outside the gate. • All switches in maintained action mode must be positioned so that the moving
gates leaves, the transit areas and vehicle thru-ways are completely visible, and yet the switches must be also away from any moving parts • Unless
the action is key operated, the control devices must be fi tted at, at least, 1.5 m from the ground and must not be accessible to the public. • To pass
the collision force test use a suitable sensitive safety-edge. Install it properly and adjust as needed. • Before handing over to users, check that the
system is compliant with the 2006/42/CE uniformed Machinery Directive • Make sure the settings on the operator are all suitable and that any safety
and protection devices, and also the manual release, work properly. • Affi x a permanent tag, that describes how to use the manual release mecha-
nism, close to the mechanism. • Make sure to hand over to the end user, all operating manuals for the products that make up the fi nal machinery.
-
The next fi gure shows the main hazard points for people
-