![Cambium Networks PTP 820 Series Скачать руководство пользователя страница 866](http://html.mh-extra.com/html/cambium-networks/ptp-820-series/ptp-820-series_user-manual_485676866.webp)
Chapter 18: Ethernet Services and Interfaces (CLI)
Viewing Ethernet PMs and Statistics (CLI)
phn-3965_006v002
Page 18-47
Parameter
Definition
RX Bytes Layer1 Exceed
Threshold (sec)
The number of seconds during the measured time interval that the RX
rate exceeded the configured threshold.
Peak RX Bytes in Layer2
The peak RX rate, in bytes per second, for the measured time interval
(excluding preamble and IFG).
Average RX Bytes in
Layer2
The average RX rate, in bytes per second, for the measured time
interval (excluding preamble and IFG).
Peak TX Packets
The peak rate of TX packets per second for the measured time interval.
Average TX Packets
The average rate of TX packets per second for the measured time
interval.
Peak TX Broadcast Packets
The peak rate of TX broadcast packets per second for the measured
time interval.
Average TX Broadcast
Packets
The average rate of TX broadcast packets per second for the measured
time interval.
Peak TX Multicast Packets
The peak rate of TX multicast packets per second for the measured time
interval.
Average TX Multicast
Packets
The average rate of TX multicast packets per second for the measured
time interval.
Peak TX Bytes in Layer1
The peak TX rate, in bytes per second, for the measured time interval
(including preamble and IFG).
Average TX Bytes in Layer1 The average TX rate, in bytes per second, for the measured time interval
(including preamble and IFG).
TX Bytes Layer1 Exceed
Threshold (sec)
The number of seconds during the measured time interval that the TX
rate exceeded the configured threshold.
Peak TX Bytes in Layer2
The peak TX rate, in bytes per second, for the measured time interval
(excluding preamble and IFG).
Average TX Bytes in Layer2 The average TX rate, in bytes per second, for the measured time interval
(excluding preamble and IFG).
Clearing Ethernet Port PMs (CLI)
To clear all PMs for an Ethernet interface, go to interface view for the interface and enter the following command:
eth type eth [x/x]> pm clear-all
Содержание PTP 820 Series
