Cambium Networks PTP 820 Series Скачать руководство пользователя страница 138

Страница: 138 / 179

Installation Guide for RFU-D-HP

Page 138 of 179

Procedure

1 Before attaching the U-Bend, make sure that the U-Bend is already fitted with bushings in both ports.

The U-Bend should be supplied with bushings to seal the RF.

2 Short U-Bends are connected between adjacent radio ports on the side closest to the Pole Mount. Place

the U-Bend so that the embedded #8-32 socket hex screws are in line with the radio ports of the OCUs,
as shown in the figure below. Make sure the sealing gaskets supplied with the U-Bend are in place
before mounting the U-Bends.

Assembling a Long U-Bend

Long U-Bends are used to connect the radio ports of adjacent OCUs on the far side from the pole mount.

List of Items

Item

Description

Quantity

RFU-D-HP Branching Long U-Bend
Kit

Depends on
Configuration

FXDH-RM-LU-Bend-06
FXDH-RM-LU-Bend-7-8
FXDH-RM-LU-Bend-11

#8-32 Socket Hex Screws

12 Per U-Bend

Embedded in U-Bend

Sealing Gaskets

Use 2.5 Nm Torque

Содержание PTP 820 Series




















































































































































































Результаты поиска

Содержание PTP 820 Series

Отзывы:

Бренды по названию

Популярные бренды

Cambium Networks PTP 820 Series, Руководство по установке

Результаты поиска

Содержание PTP 820 Series

Отзывы:

Бренды по названию

Популярные бренды