Cambium Networks PMP 450 Series Скачать руководство пользователя

Страница: 81 / 292

Chapter 2: System hardware

Cambium description

Cambium part number

Line Cord, Fig 8 – US

N000065L003A

Line Cord, Fig 8 – UK

N000065L004A

Line Cord, Fig 8 – EU

N000065L005A

Power over Ethernet midspan, 60 W, -48 V DC Input

N000000L036A

AC Pow er Inject or N0 0 0 0 65L0 0 1B

The AC Power Injector interfaces are shown in AC Power Injector interfaces and described in AC Power
Injector interface functions.

Figure 21 :

AC Power Injector interfaces

Table 54 :AC Power Injector interface functions

Interface

Function

AC power in

AC power input (main supply)

ODU

RJ45 socket for connecting Cat5e cable to ODU

LAN

RJ45 socket for connecting Cat5e cable to network

Power (green) LED

Power supply detection

ODU m o unt ing b racket s & accesso ries

The list of supported brackets is provided in Accessories part numbers.

The "Tilt bracket assembly" is the recommended bracket for the AP, SM or BH integrated units.

The "Mounting Bracket (Connectorized)" can be used where a low profile and ease of assembly of
Connectorized AP, SM or BH is required.

Содержание PMP 450 Series





































































































































































































































































































Результаты поиска

Содержание PMP 450 Series

Отзывы:

Похожие инструкции для PMP 450 Series

Бренды по названию

Популярные бренды

Cambium Networks PMP 450 Series, Руководство по установке

Результаты поиска

Содержание PMP 450 Series

Отзывы:

Похожие инструкции для PMP 450 Series

Бренды по названию

Популярные бренды