Cambium Networks PMP 450 Series Скачать руководство пользователя | Manualshive

Страница: 165 / 292

background image

Chapter 3: System planning

165

Figure 63 :

Cambium networks management domain

Net w or k A d d r ess Tr anslat ion ( NA T)

NAT, DHCP Server, DHCP Client and DMZ in SM

The system provides NAT (network address translation) for SMs in the following combinations of NAT and
DHCP (Dynamic Host Configuration Protocol):

l

NAT Disabled

l

NAT with DHCP Client (DHCP selected as the Connection Type of the WAN interface) and DHCP
Server

l

NAT with DHCP Client (DHCP selected as the Connection Type of the WAN interface)

l

NAT with DHCP Server

l

NAT without DHCP

NAT

NAT isolates devices connected to the Ethernet/wired side of a SM from being seen directly from the
wireless side of the SM. With NAT enabled, the SM has an IP address for transport traffic (separate from its
address for management), terminates transport traffic, and allows you to assign a range of IP addresses to
devices that are connected to the Ethernet/wired side of the SM.

In the Cambium system, NAT supports many protocols, including HTTP, ICMP (Internet Control Message
Protocols), and FTP (File Transfer Protocol). For virtual private network (VPN) implementation, L2TP over
IPSec (Level 2 Tunneling Protocol over IP Security) and PPTP (Point to Point Tunneling Protocol) are
supported.

«
...
163
164
165
166
167
...
»

Содержание PMP 450 Series





































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для PMP 450 Series

Бренд: Moxa Technologies Страницы: 20

Бренд: CenturyLink Страницы: 14

Бренд: TP-Link Страницы: 2

Бренд: Ubee Страницы: 2

Бренд: Aruba Страницы: 2

Бренд: ZyXEL Communications Страницы: 2

Бренд: Cambium Networks Страницы: 61

Бренд: Linksys Страницы: 112

Бренд: Linksys Страницы: 155

Бренд: NEC Страницы: 4

Бренд: Advantech Страницы: 46

Бренд: IP-COM Страницы: 15

Бренд: IP-COM Страницы: 63

Бренд: DQ Technology Страницы: 43

Бренд: Brickcom Страницы: 52

Бренд: Nortel Страницы: 34

Бренд: Draytek Страницы: 207

iNELS RFSAI-62B

Бренд: Elko Страницы: 7

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды