Cambium Networks cnPilot R200 Скачать руководство пользователя страница 55 | Manualshive

Страница: 55 / 151

background image

Chapter 3: Advanced Configuration

Network

Page

53

Viewing WAN port status

To view the status of WAN port:
1. Navigate to Status page.

IPv6 DHCP configuration for LAN/WLAN clients

Wired and wireless clients connected to cnPilot Home Routers can obtain their IPv6 addresses based

on how the LAN side DHCPv6 parameters are configured. The cnPilot Home Routers can be either

configured as a DHCPv6 server in which the LAN/WLAN clients get IPv6 addresses from the
configured pool.
If DHCP server is disabled on the cnPilot Home Routers, the clients will get IPv6 addresses from the
external DHCPv6 server configured in the network.

LAN DHCPv6

When IPv6 is enabled, the LAN/WLAN clients of cnPilot Home Routers can be configured to receive
IPv6 addresses from locally configured IPv6 pool or from an external DHCPv6 server.
To enable LAN DHCPv6 service:

«
...
53
54
55
56
57
...
»

Содержание cnPilot R200
























































































































































Отзывы:

Нет отзывов

Похожие инструкции для cnPilot R200

Бренд: Aastra Страницы: 2

Ray 3 Plus Client

Бренд: Sun Microsystems Страницы: 6

Бренд: Tripp Lite Страницы: 20

Бренд: Belkin Страницы: 72

Бренд: Helmholz Страницы: 28

Total Access 1500 Dual FXS/DPO

Бренд: ADTRAN Страницы: 2

Бренд: Edge-Core Страницы: 64

Бренд: Black Box Страницы: 12

Бренд: Nexxt Страницы: 2

ExtremeCloud Appliance E1120

Бренд: Extreme Networks Страницы: 219

Бренд: Tenda Страницы: 82

Бренд: Axis Страницы: 64

Бренд: SHOWTEC Страницы: 15

Бренд: AMCI Страницы: 55

Бренд: Paradyne Страницы: 1

Бренд: Addi-Data Страницы: 20

Бренд: CHINT Страницы: 12

Бренд: MikroTik Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды