Cambium Networks cnPilot R200 Скачать руководство пользователя страница 31

Страница: 31 / 151

Chapter 3: Advanced Configuration

Setting the Time Zone

Page

Setting the Time Zone

Table 8 Setting time zone

Field Name

Description

NTP Enable

Enable NTP (Network Time Protocol) to automatically retrieve time
and date settings for the device

Current Time

When NTP Enable is set to “Disable”, manually configure the time
and date via the Current Time parameter

Sync with host

Press

button to synchronize the host PC date, time

and time zone.

Primary NTP Server

Primary and secondary NTP server address for clock synchronization.
A valid NTP server must be reachable for full NTP functionality.

Secondary NTP Server

NTP Synchronization
(1- 1440m)

The synchronization period with NTP (1-1440 minutes), default is 60

Содержание cnPilot R200
























































































































































Результаты поиска

Содержание cnPilot R200

Отзывы:

Похожие инструкции для cnPilot R200

Бренды по названию

Популярные бренды

Cambium Networks cnPilot R200, Руководство пользователя

Результаты поиска

Содержание cnPilot R200

Отзывы:

Похожие инструкции для cnPilot R200

Бренды по названию

Популярные бренды