Cambium Networks cnPilot R200 Скачать руководство пользователя страница 120 | Manualshive

Страница: 120 / 151

background image

Chapter 3: Advanced Configuration

Administration

Page

118

TR-069

TR-069 provides the possibility of auto configuration of internet access devices and reduces the
cost of management. TR-069 (short for Technical Report 069) is a DSL Forum technical
specification entitled CPE WAN Management Protocol (CWMP). It defines an application layer
protocol for remote management of end-user devices. Using TR-069, the terminals establish
connection with the Auto Configuration Servers (ACS) and get configured automatically.

Device Configuration using TR-069

The TR-069 configuration page is available under Administration menu.

Table 77 TR069

Field Name

Description

ACS parameters

TR069 Enable

Enable or Disable TR069

CWMP

Enable or Disable CWMP

ACS URL

ACS URL address

User Name

ACS username

Password

ACS password

«
...
118
119
120
121
122
...
»

Содержание cnPilot R200
























































































































































Отзывы:

Нет отзывов

Похожие инструкции для cnPilot R200

Бренд: H3C Страницы: 45

Бренд: H3C Страницы: 80

Бренд: H3C Страницы: 46

Бренд: H3C Страницы: 45

Бренд: H3C Страницы: 4

Бренд: H3C Страницы: 184

Бренд: Hama Страницы: 10

Бренд: IBM Страницы: 32

JetWeb JX2-PR0FI1

Бренд: Jetter Страницы: 67

Бренд: Lanner Страницы: 109

Бренд: Garderos Страницы: 23

Бренд: iBall Baton Страницы: 9

RUGGEDMAX WIN7000

Бренд: RuggedCom Страницы: 42

RS-232/422/485 Serial Card CE 3PXCC4A

Бренд: B&B Electronics Страницы: 47

Бренд: Valcom Страницы: 4

Бренд: ADTRAN Страницы: 161

Network Scanning Unit A

Бренд: Ricoh Страницы: 206

Бренд: 3Com Страницы: 212

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды