Model:
cnPilot e435W Indoor
Dual Gang Mounting
General Wall Mounting
Desktop Mounting
Introduction
The guide provides a quick installation process.
Tool Requirements
Single Gang Mounting
• Philips Head Screwdriver
• Torx Security Screwdriver
Single Gang Mounting
community.cambiumnetworks.com
JOIN THE CONVERSATION
Product Overview
Package Contents
e435W Access Point
Torx Screw
Size: M3 x 6mm
Quantity: 1
Single Gang Wall Bracket
Ethernet Jumper Cable
Tools Required
Multi-color LED
Dual Gang Mounting
Secure e435W to the bracket with a screw at
the bottom edge of e435W using standard Torx
security screw or standard Philips head screw.
PASS THRU
48V/ 1A
Kensington
Lock Slot
Reset
Button
cn
Pilot
TM
e
435W
Indoor
802.11ac Wave2 Dual Band
Wall Plate Wi-Fi Access Point
Quick Start Guide
Air vents
ETH2
ETH3
ETH4/
PoE OUT
Slots for bracket
mounting
Eth1/
PoE IN
PASS
THRU
Connect Ethernet cable
to the upper RJ-45 port
labeled Eth1/PoE at the
rear side of e435W to
provide connectivity.
Use the other RJ-45 port
labeled PASS-Through
for any additional cable
that might need to pass
through e435W.
Remove single-gang
box cover.
Place Cambium
single-gang wall
bracket on the gang
box and secure with at
least 2 screws.
1.
2.
3.
5.
Align the two slots at
rear side of the e435W
with two hooks on the
bracket.
4.
Remove dual-gang box
cover.
1.
2.
4.
Connect Ethernet cable
to the upper RJ-45 port
labeled Eth1/PoE at the
rear side of e435W to
provide connectivity. Use
the other RJ-45 port
labeled Pass-thru for any
additional cable that
might need to pass
through e435W.
Align the two slots at
rear side of the e435W
with two hooks on the
bracket.
5.
Secure e435W to the
bracket with a screw at
the bottom edge of
e435W using standard
Philips head or Torx
security screwdriver.
6.
Place Cambium
dual-gang wall bracket
on the gang box and
secure with at least two
screws.
Choose location on the wall to
mount the bracket using the
four mounting screws and
anchors (if needed).
Connect the short Ethernet
jumper cable between the two
RJ-45 connections on the rear
side of e435W.
Secure e435W to the bracket
using Torx (or standard) screw
on the lower edge of e435W.
Connect the short Ethernet
jumper cable between the
two RJ-45 connections at
the rear side of e435W.
Philips Head Screw
Size: M3.5 x 25mm
Quantity: 4
1.
2.
Mount e435W into the Generic
Wall bracket by aligning the
hooks.
3.
4.
Power e435W either with a
48Vdc/1A power adapter or
using the PASS-THRU port at
the bottom edge of the device
using Ethernet power.
.
5.
1.
Insert the e435W into the
desk stand plastic jumper
cable cover.
Secure the e435W and
plastic jumper cable cover
to the metal stand by
aligning the screw holes
and inserting Torx screw.
2.
3.
Power e435W either with a
48Vdc/1A power adapter or using
the PASS-THRU port at the
bottom edge of the device.
4.
3.
Slide the plastic cover
over the exposed
portion next to the
mounted e435W.
Philips Drive Pan Head Screw
Size: M3 x 6mm
Quantity: 1
