background image

Page 10

Page 11

When the green service indicator light on the front of the boiler is 
showing solid colour, the machine has been starved of water for in 
excess of 20 minutes and the solenoid valve has been disabled to 
prevent damage to the solenoid coil through overheat. To re-energise 
the solenoid, the unit must be disconnected from the electrical supply 
and then switched back on, after first reinstating the water supply.

If the unit requires servicing the service indicator will flash a sequence 
of  light pulses . A 2x or 3x-light pulse generally indicates that the low 
or normal level probes require de-scaling.
A 4x-light pulse means the water level has reached the high level 
sensor and the likelihood is that the normal level sensor requires 
de-scaling, or the machine has over-filled due to debris trapped in 
the solenoid valve. The debris can be removed by drawing plenty of  
water from the dispense valve, causing the solenoid valve to operate 
and flush out the obstruction. The machine will reset itself once the 
problem has cleared. If this does not rectify the problem, turn off the 
water supply and remove the flexible hose to check for debris in the 
valve’s filter. The unit can be used normally while the service indicator 
is flashing a 4x pulse. For further assistance, contact our service 
department on 0113 249 6681, e-mail [email protected] or find a 
local service engineer at www.calomax.co.uk

Once the outer casing is removed, access to the Service Area has 
been gained. This access must be restricted to persons having 
knowledge and practical experience of the appliance, in particular 
as far as safety and hygiene are concerned.

De-scale

To gain access to internal components, the body lid must be removed. 
The lid incorporates a condenser mechanism which must be fitted the 
correct way round. The lid is labelled accordingly. To remove the lid, 

break the lid gasket seal and pull the lid forward and up, to the front of 
the machine before lifting it clear of the body.

SERVICE INSTRUCTIONS

CONTINUED ON PAGE 14

Plug-in time switch

Ref. 7DPIT

Max 3kW

Water filter kit

(To reduce taste & odour problems)

Ref. 10TOSCK

Ref. 10TOSC

(Filter & timestrip replacement for
kit shown above)

For more information visit our website at www.calomax.co.uk or call 0113 249 6681

Fused spur time switch

Ref. 7DFST

Max 3kW

Содержание QUASAR 2














Отзывы: