background image

THE SPECIFICATIONS AND INFORMATION REGARDING THE PRODUCTS IN THIS MANUAL ARE SUBJECT TO CHANGE 
WITHOUT NOTICE, ALL STATEMENTS, INFORMATION, AND RECOMMENDATIONS ARE BELIEVED TO BE ACCURATE BUT 
ARE PRESENTED WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED. USERS MUST TAKE FULL RESPONSIBILITY 
FOR THEIR APPLICATION OF ANY PRODUCTS.
THE SOFTWARE LICENSE AND LIMITED WARRANTY FOR THE ACCOMPANYING PRODUCT ARE SET FORTH IN THE INFOR-
MATION PACKET THAT SHIPPED WITH THE PRODUCT AND ARE INCORPORATED HEREIN BY THIS REFERENCE. IF YOU 
ARE UNABLE TO LOCATE THE SOFTWARE LICENSE OR LIMITED WARRANTY, CONTACT YOUR CALIX REPRESENTATIVE 
FOR A COPY.
MANDATORY REGULATIONS AND SAFETY WARNINGS ARE PROVIDED IT IS THE RESPONSIBILITY OF THE USER TO READ 
THIS APPENDIX PRIOR TO INSTALLATION OF THIS PRODUCT.
The following third-party software may be included with your product and will be subject to the software license agree-
ment:
Network Time Protocol (NTP). Copyright © 1992, David L. Mills. The University of Delaware makes no representations 
about the suitability of this software for any purpose. 
NOTWITHSTANDING ANY OTHER WARRANTY HEREIN, ALL DOCUMENT FILES AND SOFTWARE OF THESE SUPPLIERS 
ARE PROVIDED “AS IS” WITH ALL FAULTS. CALIX AND THE ABOVE-NAMED SUPPLIERS DISCLAIM ALL WARRANTIES, 
EXPRESSED OR IMPLIED, INCLUDING, WITHOUT LIMITATION, THOSE OF MERCHANTABILITY, FITNESS FOR A PARTICU-
LAR PURPOSE AND NONINFRINGEMENT OR ARISING FROM A COURSE OF DEALING, USAGE, OR TRADE PRACTICE. 
IN NO EVENT SHALL CALIX OR ITS SUPPLIERS BE LIABLE FOR ANY INDIRECT, SPECIAL, CONSEQUENTIAL, OR INCIDEN-
TAL DAMAGES, INCLUDING, WITHOUT LIMITATION, LOST PROFITS OR LOSS OR DAMAGE TO DATA ARISING OUT OF THE 
USE OR INABILITY TO USE THIS MANUAL, EVEN IF CALIX OR ITS SUPPLIERS HAVE BEEN ADVISED OF THE POSSIBILITY 
OF SUCH DAMAGES.
Calix, Inc. products are not designed or authorized for use as a component in any life support, life safety, or other compa-
rable application. Our products should not be used in any application where the failure or faulty performances of the prod-
uct might result in a risk of personal injury or death. Buyer assumes all risk of loss, damage or injury alleged to arise from 
the failure or faulty performance of a Calix product in any unauthorized application. Buyer agrees to indemnify and hold 
harmless Calix, Inc., and its officers, directors, employees, agents, representatives, and sales partners, from any and all 
claims, costs, damages, losses, and expenses (including reasonable attorney fees) which arise from or are alleged to have 
been caused by any claim for personal injury or death connected with Buyer’s use of a Calix product in any unauthorized 
application, including claims which allege that Calix has been negligent in connection with the design or manufacture of 
the product.
B6-001, B6-006, B6-012, B6-012i, B6-150, B6-151, B6-152, B6-212, B6-214, B6-216, B6-246, B6-252, B6-312, B6-314, 

 

B6-316, B6-322, B6-440, B6-450, B6-640, and B6-660 are registered trademarks of Calix, Inc. 
 Copyright © Calix, Inc. All rights reserved. 

Содержание 2364 ONT










































Отзывы: