For spout with 4-way tee:
-Remove the Tee, Flange Nut and Stainless Steel Washer.
-Insert the spout through center hole of the sink or
countertop.
-Place Washer and Flange Nut onto Shank
from below. Align spout and tighten Flange Nut until Spout is
firmly in place.
-With O-Ring in place on end of Shank, slide Tee onto Shank.
-Place the Rubber Washer, Brass Washer and Nut
onto Nipple and tighten.
Stainless Washer
Flange Nut
Rubber Washer
Nut
Brass Washer
1"
1"
1/2"x3/8"x12"
Flex Line
Bottom
Nut
Brass
Supplied Nut
Min. 8"
INSTALLATION
INSTRUCTIONS
4-Way Tee Shown
Fig. 2
Fig. 1
Lock Nut
***NOTE: SHUT OFF WATER SUPPLY BEFORE BEGINNING INSTALLATION***
For spout with 3-way tee:
-Remove the tee, lock nut and notched washer.
-Insert the spout through center hole of the sink or
countertop.
-Slip the notched washer over spout shank. Align
notch for pop-up rod to pass through, then thread
lock nut onto the spout shank. Align spout
and tighten nut firmly.
-Place white washer into top of tee and screw
assembly onto spout shank.
-Insert lift rod through top of spout
O-Ring
(If necessary apply grease)
Notched Washer
Lock Nut
Fig. 3
Nipple
Shank
Rubber Washer
Flow Restrictor
& Rubber Washer
(For use on model
#5302 only)
1
Install spout according to the type of tee it has:
OR
Shank
WIDESPREAD FAUCETS
IMPORTANT
All
products are engineered to provide quality performance provided
they are installed and operated properly. To fully enjoy the comfort, safety, and reliability of your
new Widespread Faucet, please follow the instructions below.
All Widespread faucets meet ASME A112.18.1-2005/CSA B125.1-05
Maximum flow rate: 1.5 gpm (5.7 L/min)
4-Way
Tee
3-Way
Tee
California Faucets reserves the right to make modification and specification changes at any time.
Please visit www.calfaucets.com for most current technical data.
Tel: 714-891-7797
Fax: 714-891-2478
Toll Free: 800-822-8855
www.calfaucets.com
Pg 1
WS_ii_120917
NOTE: Due to sediment in the water it may
be necessary on occasion to remove the aerator
and clean the screen with a soft bristle toothbrush.
Please refer to Finish Care Instructions for complete
cleaning information. Wipe frequently with a soft, damp
cloth. Never use acids, harsh abrasives or detergents
.
IMPORTANT CLEANING NOTICE
Fiber
Washer
Stainless Washer
(1 1/8" Hole size for
Handle
Escutcheon
Decorative
Base Ring
Set Screw
Sink/
Countertop
drilling, recommended)
Hot
Cold
"A"
Handle
Series # "A"
DIMENSION
"A"
"A" Dimension is from sink/countertop
to tip of stem broach
32 2 3/8" 53 2 1/4"
33 2 3/8" 55 2 5/8"
34 2 3/8" 57 2"
35 2 3/8" 58 2 5/8"
36 2 3/8" 59 2 5/8"
38 2 5/8" 60 2 1/4"
40 2 5/8" 61 2 1/4"
42 2 5/8" 63 3"
43 2 1/4" 64 2 5/8"
44 2 7/16" 65 2 1/8"
46 2 1/2" 66 2 1/8"
47 2 1/2" 67 2 1/4"
50 2 1/4" 68 2 3/8"
51 2 1/2" 69 2 3/8"
52 2 5/8"
Handle
Series # "A"
®
