Cajun P220G Скачать руководство пользователя страница 17

Страница: 17 / 135

Configuring the P220G Gigabit Switch

2-2 Cajun P220G Switch Configuration and Operation Guide

To connect to the Web Agent, you must first use the serial command line interface to
give the supervisor module an IP address and a subnetwork mask. To connect to the Web
Agent, complete the following steps:

1. Start the switch as instructed in the Cajun P220G Switch Installation Guide.

2. Attach a serial cable from the serial port on your PC to the serial port on the

switch’s front panel using a 9-pin straight-through male-to-female serial cable.

3. Run a terminal emulation program (HyperTerminal, for example) on the attached

PC. Make sure that the terminal settings match those listed in Table 2-1.

4. Press Enter on the PC’s keyboard. The following prompt displays:

Lucent Technologies P220G Switch Agent v1.x.x

Press Ctrl-P for previous command, Ctrl-N for next command, ? for help.

Note: The user name and password are case sensitive.

5. Enter the username “root”. The terminal prompts for a password.

Password:

6. Enter “root” (the default password), then press Enter. The command prompt

displays.

7. Enter the following command:

P220G Switch> net ip address ethernet_console <ip address> <ip mask>

Where:

is the IP address of the switch and

is the subnetwork

mask. The mask must be in decimal numbers (255.255.255.0, for example).

Note: The inband IP address is associated with the default VLAN by default. Refer

to Chapter 8 to change the default to a different VLAN.

8. Press Enter.

9. Enter a default gateway (first hop router) for the subnetwork this switch connects

to using the following command:

P220G Switch> net ip default_gateway ethernet_console <address>

Where:

is the address of the router port.

Содержание P220G








































































































































Результаты поиска

Содержание P220G

Отзывы:

Похожие инструкции для P220G

Бренды по названию

Популярные бренды

Cajun P220G, Руководство по конфигурации и эксплуатации

Результаты поиска

Содержание P220G

Отзывы:

Похожие инструкции для P220G

Бренды по названию

Популярные бренды