background image

 DAMC-FMC2ZUP User’s Manual 

 

Introduction 

 

The  card  provides  two  FMC  sockets,  one  FMC+  (VITA  57.4  compliant)  and  one 

FMC  High  Pin  Count  (VITA  57.1  compliant).  Both  connectors  populate  all  LA  and 

HA differential  pair lines  and can operate on VADJ  level  in  the range  from 1.2V to 

1.8V. A total of 24 transceivers are routed to the FMC+ socket and 8 to the FMC HPC 

connector. Front panel connectivity comprises a Micro HDMI type-D connector with 

a proprietary pin assignment offering a Gigabit Ethernet interface (over external SFP), 

clock input and two trigger in/out signals. The front panel Gigabit Ethernet connection 

can be used in conjunction with the available HW infrastructure provided on the board 

to implement a White Rabbit endpoint.  

A fully fledged USB Type-C connector implementing Alternate Mode Display 

Port is connected to the PS, this allows to provide USB HS, USB SS 3.0, DisplayPort 

and  power  delivery  capabilities  on  a  single  compact  interface.  This  offers  the 

possibility to omit a CPU boards in the MicroTCA systems.  

The  RTM  interface  is  designed  according  to  class  D1.1  and  implements  the 

full  set  of  42  LVDS  lines  and  2  MGT  links.  The  board  supports  all  existing  digital 

RTMs from DESY (i.e. DRTM-AD84, DRTM-VM2, DRTM-PZT4).  

The  ARM  Cortex-A53  processor  in  the  MPSoC  can  run  GNU/Linux  from  a 

MicroSD card on the front panel or from the embedded 8GB eMMC flash memory. 
The  Zynq  Ult  family  of  FPGAs  is  supported  by  all  modern  development 

tools,  such  as  Vivado,  HLS,  Yocto,  Petalinux,  SDSoC  and  SDAccel,  this  makes 

DAMC-FMC2ZUP capable of addressing the ever-growing need of processing power 

while also reducing development time. 

 

1.2

 

DAMC-FMC2ZUP Features 

 

Two FPGA Low-Power Xilinx MPSoC Ult options are available: 

  

MPSoC FPGA 

ZU11EG-L2 

ZU19EG-L2 

Logic Cells 

653 k 

1.143 k 

DSP Slices 

2.928 

1.968 

BlockRAM 

21.1 MiB 

34.6 MiB 

UltraRAM 

22.5 MiB 

36.0 MiB 

PCIe 

Gen. 3 x4 or x8 

Ethernet MAC 

100G 

ARMs 

1.333 GHz Quad-Core ARM Cortex-A53, 

MALI-400 GPU, 600 Mhz Dual-core ARM 

Cortex-R5 

GTY 

transceivers 

16 GTY transceivers (28.21 Gbps) routed to 

FMC+ transceivers 

GTH 

32 GTH Transceivers (16.375 Gbps/ 12.5 Gbps 

Содержание DAMC-FMC2ZUP



































Отзывы: