CAENels DAMC-FMC2ZUP Скачать руководство пользователя страница 20 | Manualshive

Страница: 20 / 34

CAENels DAMC-FMC2ZUP Скачать руководство пользователя страница 20

DAMC-FMC2ZUP User’s Manual

DAMC-FMC2ZUP Architecture

20

2.3

Power Supply Architecture

The power supply section is implemented by a cascade of DC/DC converters and

LDOs, all of which are controlled by a PMBus manager IC, this ensures that the

proper sequencing, as required by the FPGA and IC speciﬁcations, is maintained both

at start-up and power-down. The PMBus manager offers full telemetry and

monitoring of the power rails (voltage and current readouts) and is responsible to

bring the board to a safe condition whenever a supply voltage is out of speciﬁcations.

This component also allows trimming the output voltages and it’s responsible to

set the VADJ rail to the voltage level required by the FMC modules. The MMC

Stamp SoM has full control over the power conversion stages through the PMBus

manager. By interfacing to the MCH the user can access the readout values for the

following power rails:

•

0.72/0.85 V Main FPGA Core

•

1.0 V Secondary FPGA Core

•

TBD

A general overview of the power section is presented in Figure 2.3.

Figure 2-3:

Power-Supply Section

«
...
18
19
20
21
22
...
»

Содержание DAMC-FMC2ZUP



































Отзывы:

Нет отзывов