Cadillac Escalade 2020 Скачать руководство пользователя страница 300 | Manualshive

Страница: 300 / 355

background image

Cadillac Escalade Owner Manual (GMNA-Localizing-MidEast-13566599) -

2020 - CRC - 5/29/19

300

VEHICLE CARE

necessary on a regular basis. Consider
an alignment check if there is unusual
tire wear or the vehicle is significantly
pulling to one side or the other. Some
slight pull to the left or right,
depending on the crown of the road
and/or other road surface variations
such as troughs or ruts, is normal.
If the vehicle is vibrating when driving
on a smooth road, the tires and
wheels may need to be rebalanced.
See your dealer for proper diagnosis.

Wheel Replacement

Replace any wheel that is bent,
cracked, or badly rusted or corroded.
If wheel nuts keep coming loose, the
wheel, wheel bolts, and wheel nuts
should be replaced. If the wheel leaks
air, replace it. Some aluminum wheels
can be repaired. See your dealer if any
of these conditions exist.

Your dealer will know the kind of
wheel that is needed.

Each new wheel should have the same
load-carrying capacity, diameter,
width, offset, and be mounted the
same way as the one it replaces.

Replace wheels, wheel bolts, wheel
nuts, or Tire Pressure Monitor System
(TPMS) sensors with new GM original
equipment parts.

{

Warning

Using the wrong replacement
wheels, wheel bolts, or wheel nuts
can be dangerous. It could affect
the braking and handling of the
vehicle. Tires can lose air, and
cause loss of control, causing a
crash. Always use the correct wheel,
wheel bolts, and wheel nuts for
replacement.

Caution

The wrong wheel can also cause
problems with bearing life, brake
cooling, speedometer or odometer
calibration, headlamp aim, bumper
height, vehicle ground clearance,
and tire or tire chain clearance to
the body and chassis.

Used Replacement Wheels

{

Warning

Replacing a wheel with a used one
is dangerous. How it has been used
or how far it has been driven may
be unknown. It could fail suddenly
and cause a crash. When replacing
wheels, use a new GM original
equipment wheel.

Tire Chains

{

Warning

Do not use tire chains. There is not
enough clearance. Tire chains used
on a vehicle without the proper
amount of clearance can cause
damage to the brakes, suspension,
or other vehicle parts. The area
damaged by the tire chains could
cause loss of control and a crash.
Use another type of traction device
only if its manufacturer

(Continued)

«
...
298
299
300
301
302
...
»

Содержание Escalade 2020




































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Escalade 2020

Бренд: Suzuki Страницы: 16

Бренд: Abarth Страницы: 176

Бренд: UMBRA RIMORCHI Страницы: 18

Бренд: DEFA Страницы: 9

Slim Line LED Light Grille Kit

Бренд: rough country Страницы: 8

Бренд: Vintage Air Страницы: 28

Бренд: Fiat Страницы: 172

Бренд: Honda Страницы: 6

Green Motion DC 66

Бренд: Eaton Страницы: 18

Бренд: Xhorse Страницы: 48

Бренд: Meta System Страницы: 22

2000 Oldsmobile Intrigue

Бренд: Oldsmobile Страницы: 348

Бренд: Mercedes-Benz Страницы: 10

CF-UFORCE-DRW01

Бренд: FALCON RIDGE Страницы: 6

Бренд: Blaupunkt Страницы: 6

Outlander Plug-in hybrid

Бренд: Mitsubishi Страницы: 28

Бренд: Arctic Cat Страницы: 101

Бренд: GEMINI TECHNOLOGY Страницы: 9

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды