Cadillac Escalade 2020 Скачать руководство пользователя страница 290 | Manualshive

Страница: 290 / 355

background image

Cadillac Escalade Owner Manual (GMNA-Localizing-MidEast-13566599) -

2020 - CRC - 5/29/19

290

VEHICLE CARE

pressure needed to support the
vehicle's maximum load carrying
capacity.

For additional information
regarding how much weight the
vehicle can carry, and an example
of the Tire and Loading
Information label, see

. How the vehicle is

loaded affects vehicle handling
and ride comfort. Never load the
vehicle with more weight than it
was designed to carry.

When to Check

Check the pressure of the tires
once a month or more.

Do not forget the spare tire, if the
vehicle has one. See

Full-Size Spare

for additional

information.

How to Check

Use a good quality pocket-type
gauge to check tire pressure.
Proper tire inflation cannot be
determined by looking at the tire.

Check the tire inflation pressure
when the tires are cold, meaning
the vehicle has not been driven for
at least three hours or no more
than 1.6 km (1 mi).

Remove the valve cap from the
tire valve stem. Press the tire
gauge firmly onto the valve to get
a pressure measurement. If the
cold tire inflation pressure
matches the recommended
pressure on the Tire and Loading
Information label, no further
adjustment is necessary. If the
inflation pressure is low, add air
until the recommended pressure is
reached. If the inflation pressure
is high, press on the metal stem in
the center of the tire valve to
release air.

Re-check the tire pressure with
the tire gauge.

Put the valve caps back on the
valve stems to keep out dirt and
moisture and prevent leaks. Use
only valve caps designed for the

vehicle by GM. TPMS sensors
could be damaged and would not
be covered by the vehicle
warranty.

Tire Pressure for
High-Speed Operation

{

Warning

Driving at high speeds, 160 km/h
(100 mph) or higher, puts additional
strain on tires. Sustained
high-speed driving causes excessive
heat buildup and can cause sudden
tire failure. This could cause a
crash, and you or others could be
killed. Some high-speed rated tires
require inflation pressure
adjustment for high-speed
operation. When speed limits and
road conditions allow the vehicle to
be driven at high speeds, make sure
the tires are rated for high-speed
operation, are in excellent
condition, and are set to the correct
cold tire inflation pressure for the
vehicle load.

«
...
288
289
290
291
292
...
»

Содержание Escalade 2020




































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Escalade 2020

Бренд: Suzuki Страницы: 16

Бренд: Bestop Страницы: 11

Бренд: Whispbar Страницы: 14

2014 Insignia VXR SuperSport

Бренд: Vauxhall Страницы: 56

Бренд: Whispbar Страницы: 14

Бренд: Whispbar Страницы: 15

Бренд: GARO Страницы: 15

Бренд: Carcomm Страницы: 2

Бренд: Gator Страницы: 6

Бренд: Flash Cover Страницы: 2

Бренд: Carbest Страницы: 64

Бренд: Honda Страницы: 2

Gigaware 12-493

Бренд: Gigaware Страницы: 8

Бренд: Wallbox Страницы: 21

Aura Mobile BT MCP-2014

Бренд: Spracht Страницы: 2

Бренд: Cadillac Страницы: 78

Pro Competition

Бренд: G-Tech Страницы: 180

Directechs FORD11

Бренд: Directed Страницы: 23

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды