Cadillac Escalade 2020 Скачать руководство пользователя страница 201 | Manualshive

Страница: 201 / 355

background image

Cadillac Escalade Owner Manual (GMNA-Localizing-MidEast-13566599) -

2020 - CRC - 5/29/19

DRIVING AND OPERATING

201

Brake Assist

Brake Assist detects rapid brake pedal
applications due to emergency braking
situations and provides additional
braking to activate the Antilock Brake
System (ABS) if the brake pedal is not
pushed hard enough to activate ABS
normally. Minor noise, brake pedal
pulsation, and/or pedal movement
during this time may occur. Continue
to apply the brake pedal as the driving
situation dictates. Brake Assist
disengages when the brake pedal is
released.

Hill Start Assist (HSA)

{

Warning

Do not rely on the HSA feature.
HSA does not replace the need to
pay attention and drive safely. You
may not hear or feel alerts or
warnings provided by this system.
Failure to use proper care when
driving may result in injury, death,
or vehicle damage. See

.

When the vehicle is stopped on a
grade, Hill Start Assist (HSA)
temporarily prevents the vehicle from
rolling in an unintended direction
during the transition from brake pedal
release to accelerator pedal apply. The
brakes release when the accelerator
pedal is applied or automatically
release after a few seconds. The brakes
may also release under other
conditions. Do not rely on HSA to
hold the vehicle.

HSA is available when the vehicle is
facing uphill in a forward gear,
or when facing downhill in
R (Reverse). The vehicle must come to
a complete stop on a grade for HSA to
activate.

Ride Control Systems

Traction Control/Electronic
Stability Control

System Operation

The vehicle has a Traction Control
System (TCS) and StabiliTrak

®

, an

electronic stability control system.
These systems help limit wheel spin
and assist the driver in maintaining
control, especially on slippery road
conditions.

TCS activates if it senses any of the
drive wheels are spinning or beginning
to lose traction. When this happens,
TCS applies the brakes to the spinning
wheels and reduces engine power to
limit wheel spin.

StabiliTrak activates when the vehicle
senses a difference between the
intended path and the direction the
vehicle is actually traveling.
StabiliTrak selectively applies braking
pressure to any one of the vehicle
wheel brakes to assist the driver in
keeping the vehicle on the intended
path. Trailer Sway Control (TSC) is

«
...
199
200
201
202
203
...
»

Содержание Escalade 2020




































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Escalade 2020

Бренд: Samsung Страницы: 133

Бренд: TATA Motors Страницы: 94

Бренд: GÄN Страницы: 24

Бренд: Kargo Master Страницы: 13

Бренд: Kargo Master Страницы: 21

Бренд: Kargo Master Страницы: 4

Бренд: Yakima Страницы: 6

Бренд: Yakima Страницы: 18

2005 Sierra Denali

Бренд: GMC Страницы: 428

Бренд: Mercedes-Benz Страницы: 346

Бренд: Thule Страницы: 4

Бренд: WABCO Страницы: 48

Бренд: Whipple Страницы: 3

StreetLine Series

Бренд: SAAS Страницы: 4

Бренд: Rugged Ridge Страницы: 2

Бренд: Toyota Страницы: 295

CHALLENGER HELLCAT 2017

Бренд: Dodge Страницы: 484

Бренд: APS Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды