manualshive.com logo in svg

CAB 4712, Руководство по обслуживанию, Страница: 13 / 53

Поделиться
Скачать
CAB 4712 Скачать руководство пользователя страница 13

13

3.2 

Setting the Peel Position

To optimize the transfer of the labels from the printer to the pad there are two different parameters available for 
adjusting the peel position.

!

Attention!

 

First adjust the parameter "Peel Position" in the printer configuration.

 

Then adjust the additional peel-off offset in the software.

It is very important to follow that procedure for a certain start after label loading and for the re-start after 
error treatment.

Parameter "Peel Position" in the printer configuration

 

Check the basic settings in the printer setup. Perform labelling cycles by alternately pressing the 

 button 

and Enter button  

 .  

  „4.1 Test Mode without a Print Job“

 

In the submenu  

 

Labelling

 > 

 

Peel-off position 

adjust the "Peel-off position" in such a way, that the blank 

labels are peeled-off completely from the liner  

„3 Configuration on the Printer“

Peel-off offset in the software

 

Check the setting in the software. Perform labelling cycles by repeatedly pressing the button  

 

 

 

 

 „4.2 Test Mode with a Print Job“.

 

Adjust the peel-off offset in such a way, that the printed labels are peeled-off completely from the liner  

 Programming manual or software documentation.

3.3 

Activation of Peel-off Mode

i

Note!

 

For labelling operation activate the peel-off mode in the software.

 

For direct programming use the P command 

 Programming manual.  

3 

Configuration on the Printer

Содержание 4712






















































Отзывы:

Нет отзывов