C-TEC EACIE Скачать руководство пользователя страница 4 | Manualshive

Страница: 4 / 38

C-TEC EACIE Скачать руководство пользователя страница 4

EACIE Evacuation Alert Control and Indicating Equipment

Installation and Programming Manual



Approved Document No. DFU5030020 Rev 1



Page 4 of 38

Symbols

Read these instructions thoroughly before installation and operation

General Warning

Sign Danger Electrical Hazard

1

IMPORTANT NOTES

1.1

Relevant EACIE Standards



Complies with BS 8629 (if installed correctly).



Conforms to EN 54-4 (exceptions as per mandatory requirement of BS 8629).

1.2

Items Supplied



EACIE Evacuation Alert and Indicating Equipment, as ordered.



Installation, Maintenance & Programming manual (this manual) – Explains how to install,
commission and maintain the EACIE.

This manual MUST NOT be left accessible to the user

.



User Manual and Log Book (Document No. DFU5030070) – Gives detailed operational
information and details about the panel’s indicators and controls.



Quick Start User Guide (Document No. DFU5030075) and Quick Start Installation and
Programming Manual (Document No. DFU5030025).



EACIE Typical Layout Drawing (Document No. DFU5030100).



Electrical accessory pack containing:

1 x 20mm T 2A H 230V ceramic fuse (spare primary fuse)

1 x 7.5A MINI

®

automotive blade fuse (spare battery fuse)

6K8 0.25W EOL resistors for the unused sounder circuits and unused monitored inputs

1 x set of battery link wires and four cable ties

4 x screws (used to secure the EACIE chassis in the protective cabinet)

1 x set of labels for the Control/Display Module

1 x set of labels for the 8 Zone Switch/Indicator Modules

1.3

Notices

Anti-static handling guidelines

Make sure that handling precautions for electro-static devices (ESD) are taken immediately
before handling PCBs and other ESD components. Before handling any ESD items,
engineers should get rid of any electro-static charge by touching a sound safety earth.
Always handle PCBs by their sides and avoid touching any electronic components. PCBs
should be stored in a clean, dry place that is free from vibration, dust and excessive heat.

Disclaimer

Errors and omissions excepted (E&OE). No responsibility can be accepted by the manufacturer or distributors of this
range of panels for any misinterpretation of an instruction or guidance note or for the compliance of the system as a
whole. The manufacturer’s policy is one of continuous improvement and we reserve the right to make changes to product
specifications at our discretion and without prior notice.

WARNINGS!
This equipment MUST only be installed and maintained by a suitably skilled and
technically competent person.

Ensure you have attended C-TEC’s Authorised

Training Course before attempting to install and program the EACIE panel.

This equipment is a piece of Class 1 equipment and MUST BE EARTHED.

ALWAYS isolate the panel’s mains and battery backup supplies before making

connections to its PCBs.

«
...
2
3
4
5
6
...
»

Содержание EACIE







































Отзывы:

Нет отзывов