C-TEC EACIE Скачать руководство пользователя страница 37

Страница: 37 / 38

EACIE Evacuation Alert Control and Indicating Equipment

Page 37 of 38



Approved Document No. DFU5030020 Rev 1



Installation and Programming Manual

Maintenance controls:

Interactive touchscreen with menu sensitive buttons. 1 keyswitch provides entry to Access Level 2

Connections

Connections:

Fixed and plug-on connectors, largest acceptable conductor size 2.5mm

Expansion connections:

RS485 peripheral bus connection allows the connection of up to 15 'A-Bus' PCBs (2 control cores plus screen
plus 2 cores for power).

EACIE Panel Programming Module

Control / Display module:

Control/Display module c/w LCD, touchscreen, keyswitch, 16 LEDs.

Part No. Z41/CA.

Mechanical

Protective cabinet overall dimensions (mm):

700 (H) x 741 (W) x 200 (D)

Protective cabinet weight (empty):

69kg

Protective cabinet construction & finish:

Silver grey steel RAL 9006 silver grey epoxy paint

Protective cabinet locking system:

Lock certified to EN 1303

Keys (carried by registered key holder):

“N” High Security keys included

Protective cabinet compliance:

STS 205 Issue 4/BR2 BMTrada Certificate

EACIE panel overall dimensions (mm):

442 (H) x 431 (W) x 153 (D) including toggle switch heights

EACIE panel weight (excluding batteries):

7.5 - 10kg (model dependent)

EACIE panel weight (including batteries):

20 – 22.5kg (model dependent)

Environmental

Operating temperature:

-10°C to +40°C

Maximum humidity:

95 % non-condensing

Protective cabinet IP Rating (to EN 60529):

IP30

Appendix 6 – Glossary of Terms

AL1:

Access Level 1 (for general users).

AL2:

Access Level 2 (for authorised users).

AL3:

Access Level 3 (for authorised systems engineers).

ARC:

Alarm Receiving Centre.

BS 7671:

IET Wiring Regulations.

BS 8629:2019:

Evacuation Systems for Fire & Rescue Services. Code of practice for the design, installation,

commissioning and maintenance of evacuation alert systems for use by fire and rescue services in buildings
containing flats.

EACIE:

Evacuation Alert Control & Indicating Equipment. Component of an evacuation alert system through

which evacuation alert devices (sounders) can be controlled, and that is used to monitor the correct functioning
of the system and give audible and visible warning of any faults.

EAS:

Evacuation Alert System. Comprises of evacuation alert devices, sounder controllers and an EACIE

panel with manual controls for the FRS to activate the evacuation alert devices.

EN 54-2:

Fire Detection and Fire Alarm Systems. Control and Indicating Equipment.

EN 54-3:

Fire Detection and Fire Alarm Systems. Sounders.

EN 54-4:

Fire Detection and Fire Alarm Systems. Power Supply Equipment.

Evacuation Alert Device

(sounder):

Component of the evacuation alert system, not incorporated in the

EACIE, which is used to signal to the occupants of a flat that evacuation is required by the FRS.

Evacuation Alert Zone:

May contain flats, part floors, or a complete floor of a building.

FRS:

Fire & Rescue Service.

Содержание EACIE







































Результаты поиска

Содержание EACIE

Отзывы:

C-TEC EACIE, Инструкция по установке, техническому обслуживанию и эксплуатации, Страница: 37 / 38

Результаты поиска

Содержание EACIE

Отзывы: