C-TEC EACIE Скачать руководство пользователя страница 30 | Manualshive

Страница: 30 / 38

C-TEC EACIE Скачать руководство пользователя страница 30

EACIE Evacuation Alert Control and Indicating Equipment

Installation and Programming Manual



Approved Document No. DFU5030020 Rev 1



Page 30 of 38

7.5.8

Edit Zone Name

This function allows a text description to be assigned to an evacuation alert zone.

At Access Level 3 > Commissioning Functions, press the

button and a window similar to

the one shown below left appears.
To change a zone’s text description, press the text description button (‘Zone 1’ is shown as an example) and
the window shown below right appears. Amend the text using the touchscreen’s standard QWERTY keyboard
controls.

To select a different zone for editing, either press the zone number field (001 shown below left) and use the

and

buttons to scroll through the zones, or enter the zone number directly into the zone number field

using the touchscreen’s numeric keypad.

7.5.9

Edit Output Group Name

This function allows text descriptions for Output Groups to be changed.

At Access Level 3 > Commissioning Functions, press the

button and a window similar to

the one shown below appears.

Amend the text descriptions by following the same operating
procedure detailed in section 7.5.8.

7.5.10

Setup Networking

This function only applies to networked panels.

7.5.11

Synchronise Network Data

This function only applies to networked panels.

7.5.12

Set Loops Fitted

This function sets the number of loops the panel’s firmware assigns to a panel. Note that the actual physical
number of loops that can be connected to a panel is dependent on the number of loop driver modules fitted, i.e.
Main 1, 2 or 4-Loop PCB.

«
...
28
29
30
31
32
...
»

Содержание EACIE







































Отзывы:

Нет отзывов