C-TEC EACIE Скачать руководство пользователя страница 16 | Manualshive

Страница: 16 / 38

C-TEC EACIE Скачать руководство пользователя страница 16

EACIE Evacuation Alert Control and Indicating Equipment

Installation and Programming Manual



Approved Document No. DFU5030020 Rev 1



Page 16 of 38

5.8

Relay Output Wiring

One volt-free relay output connection is provided on the Main PCB - a fail-safe fault output, which switches
under any fault condition or total power failure. The relay is capable of switching 1A @ 30Vdc.

DO NOT use this relay for switching mains voltages.

This relay may be used to send a fault signal to an alarm receiving centre (ARC).

The wiring for the output should be connected to the relevant connector block on the Main 1, 2, or 4-Loop PCB
(model dependent) as shown in Figure 7 below.

Figure 7 – Relay Output Detail

Figure 7 shows the position of the relay contacts in quiescent, no fault
condition.

5.9

Remote PC Connection

Figure 8 – PC Connection

A  ‘galvanically  -  isolated’  USB  connector
(CONN3)  is  provided  on  the  Control/Display
Module  PCB  for  the  connection  of  a  Windows™
based PC running programming software.

The recommended cable is a USB Type A male
connector to USB Type B male connector.

EACIE programming tools (Part No. ZTOOLS) are
available that allow quick and easy input of data,
device and zone naming.

«
...
14
15
16
17
18
...
»

Содержание EACIE







































Отзывы:

Нет отзывов