CTX200 / *CTX 200P
Tests CAT3, 5, 5e, 6, 6A, & 7 Ethernet Cables to
TIA568 Specs • Tests COAX Cables • Locates Cables*
4
Tests and tones both RJ45-CAT5/6 and coax cables.
4
Ruggedized for field use. Small and easy to carry.
4
PASS/FAIL results appear in one second.
4
Each pair’s status is highlighted.
4
Complete TIA568 test performed. Continuity, opens / shorts, reversals and split pairs.
4
Full featured probe for tracing cables and troubleshooting.
4
Auto-off (12 seconds) to conserve battery life.
4
Low battery indicator.
4
Belt clip, battery (9V) and pouch included.
FEATURES
Purpose
Ethernet cables have 4 pairs of wires (”twisted pairs”). It is important that the pairs correctly
go to connector pins 1,2 ; 3,6 ; 4,5 ; and 7,8. The Pocket CAT tests for the proper pairing and if
there is an error it will report it to you (”split pairs”) .
Connecting cables to the Tester
Installed cables:
Connect the Main unit to the wall jack, then connect the Remote to the patch
panel or far-end wall jack.
Patch cables:
Attach the Main unit and Remote directly to the cable ends.
Power ON and Test
Press the ON button. Press again to begin test. When the PASS/FAIL LEDs light, press the
FAULT CHECK button to isolate any problems to an individual pair.
Coax Testing
Coax is displayed using the 4/5 LEDs. The coax remote is in the pouch.
QUICK START: CABLE TESTING
Purpose
Tone is used to locate a cable’s far end. A tone is placed on the cable’s “near end” by the
Pocket CAT Main unit. The probe locates the tone at the far end of the cable.
Connecting cables to the Tester
Plug the cable into the tester’s Main unit.
Power ON and Tone
:
Press the ON button. Hold the TONE button for 7 secs to turn ON the tone. Press the TONE
button repeatedly to select the pair you wish to tone. The tone is loudest when you select the
entire cable (including the shield).
QUICK START: CABLE LOCATING WITH TONE
Testing patch cables
Slide Remote Connector out from base of Pocket CAT, then connect one end
of the cable to the Remote Connector, and the other end to the Pocket CAT.
Testing installed cables
Slide Remote Connector out from base of Pocket CAT, then connect the far
end of the cable to the Remote Connector, and the other end to the Pocket
CAT.
NOTE: The Remote Connector for COAX testing is located in the pounch.
CONNECTING THE POCKET CAT
POCKET CAT FACEPLATE
Pass/Fail
Indicator
Pair/Shield
Tested
(Coax uses 4/5)
Press to test all pairs
automatically.
Press to test pairs individually.
Hold 7 secs for tone.
Press again to select pair.
OPEN: A wire is disconnected
SHORT: A wire makes contact with
another wire
CROSS (REVERSAL):
A twisted pair gets flipped on one
side of the cable
SPLIT: One wire from each of two
different pairs gets swapped on
both ends of the cable.
Remote Connector
(push to slide or remove)
ON
OFF
BLINK
TESTING RJ45 AND COAX CABLES
Power ON and TEST: Press the ON button. Press again to commence the test. The bright, blue
PASS LED indicates the cable has passed. If the FAIL LED lights, press the FAULT CHECK
button to isolate problems to an individual pair. See back for more examples.
EXAMPLE: CABLE PASSED
TEST. ALL 4 PAIRS AND
SHIELD ARE WIRED.
Coax cable: LEDs 4/5
are used for testing.
If FAIL, press FAULT CHECK
to isolate problem to an
individual pair(s).
LEDs
.
.
ON
OFF
BLINK
USING TONE TO LOCATE A CABLE END
Power ON and TONE: Hold the TONE button for 7 secs to turn ON the tone. Press the TONE
button repeatedly to select the pair(s) you wish to tone (or select them all). Coax cable uses
pair 4/5 for tone. Note: Requires an inductive probe to detect tone (included in this kit).
EXAMPLE: TONE “ON”
(ALL PAIRS + SHIELD)
SELECT A SINGLE PAIR OR
ALL PAIRS USING THE TONE
BUTTON.
Hold 7 secs for tone. Press
again to select pair(s).
LEDs
POCKET CAT
TM
NETWORK CABLE TESTER
WARNING!!!
DO NOT USE ON LIVE CIRCUITS!!
LIMITED WARRANTY
The manufacturer warrants to the original consumer that this product is in good working or-
der for a period of one year from the date of manufacture or the date of purchase. During
this period, the product will be repaired or replaced without charge for either parts or labor.
The warranty DOES NOT cover damage caused by connecting tester to high voltage
sources such as telephones or Power over Ethernet (PoE)
. Repair or replacement as
provided under this warranty is the exclusive remedy of the purchaser.
PIN #
1
2
3
6
4
5
7
8
Cable Diagrams Inside
BNC Terminator
Included
