background image

Build Your Own Clone 

 Phase Royal 

Kit Instructions 

 

 
 

Warranty: 

BYOC, LLC guarantees that your kit  will be complete and that all parts and 
components will arrive as described, functioning and free of defect.  Soldering, 
clipping, cutting, stripping, or using any of the components in any way voids this 
guarantee.  BYOC, LLC  guarantees  that the instructions for your kit will be free of  
any majors errors that would  cause you to permanently  damage any components 
in your kit, but does  not guarantee that  the instructions will be free of typos or 
minor errors.   BYOC, LLC does not warranty the completed pedal as a whole 
functioning  unit  nor do we warranty any of the individual parts once  they have 
been  used.  If you have a component that is used, but  feel it was defective  prior to 
you using it, we reserve  the right to determine whether or not the component was 
faulty upon arrival.  Please direct all warranty issues to: 

[email protected]  This would include any missing parts issues. 
 

Return: 

BYOC, LLC accepts returns and exchanges  on all products for any reason, as long  as 
they are unused.  We do not accept partial kit returns.  Returns and exchanges are for the 
full purchase price less the cost of  shipping and/or any promotional pricing.  Return 
shipping is the customers responsiblity.  This responsibility not only includes the cost of 
shipping, but accountability of deliver as well.  Please contact 
[email protected] to receieve a return authorization before mailing. 

Содержание Build Your Own Clone Phase Royal Kit


































Отзывы: